2024-07-01

Harness - Subframe - Rear (Remove and Replace)

Código de corrección 1710150012 FRT 0.96 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. Consulte Precauciones ergonómicas para ver prácticas de trabajo seguras.

  • 1060071-00-A Torque Wrench ¼ in Dr Hexagon

Retirar

  1. Place the vehicle on the 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the vehicle is not charging.
  2. Open the LH front door and lower the LH front window.
  3. Disconnect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect) (Modify).
  4. Remove the rear fascia. See Fascia Assembly - Rear (Remove and Install).
  5. Remove LH and RH rear wheels. See Conjunto de rueda (Desinstalación e instalación).
  6. Disconnect LH rear wheel speed harness.
  7. Disconnect RH rear wheel speed sensor connector.
  8. Remove RH side subframe harness clip from body.
  9. Release oil pump connector.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not push down on red tab, pull red tab to disengage lock and pull again to release connector.
  10. Release RDU logic connection.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not get coolant ingress into this connector, move aside as needed.
  11. Release RDU logic connection clip.
  12. Use the Small flat head screwdriver and the lip tool to release resolver connection (X1) and clips (X2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Move aside harness branch as needed.
  13. Release clips (X4) securing subframe harness to top of rear subframe.
  14. Use the clip tool to release clips (X2) securing subframe harness to left and right of subframe.
  15. Remove harness from subframe assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take out the harness from the gap between the RDU and the subframe and take out the harness from left to right.

Instalar

  1. Place the front subframe harness to the front subframe, and then secure the front subframe harness clips (x2) along left and right of subframe.
  2. Install clips (X4) securing subframe harness to top of rear subframe.
  3. Secure the resolver connection (X1) and clips (X2).
    Informational PurposesAn informational icon, calling your attention
    Note
    Move aside harness branch as needed.
  4. Secure oil pump connector.
  5. Secure RDU logic connection.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not get coolant ingress into this connector, move aside as needed.
  6. Secure RDU logic connection clip.
  7. Install RH side subframe harness clip from body.
  8. Connect RH rear wheel speed sensor connector.
  9. Connect LH rear wheel speed harness.
  10. Install the rear fascia. See Fascia Assembly - Rear (Remove and Install).
  11. Install LH and RH rear wheels. See Conjunto de rueda (Desinstalación e instalación).
  12. Connect the LV battery power. See LV Battery - Li-lon (Disconnect and Connect) (Modify).
  13. Raise the LH front window and close the LH front door.
  14. Remove the lift arms from below the vehicle.