2026-03-26

Rear Fascia Assembly (Model Y Standard) (Remove and Install)

Código de corrección 10011400501 0.48 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  • 2026-03-16: Released new procedure.

Desinstalar

  1. Open the LH rear door.
  2. Lower the LH rear window.
  3. Remove the LH rear fender garnish from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips, 2x tabs, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
  4. Remove the screw that secure the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x screw, 8mm, 2 Nm
  5. Remove the LH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  6. Remove the bolt that secures the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 10mm, 3.5 Nm
  7. Open the RH rear door.
  8. Lower the RH rear window.
  9. Remove the RH rear fender garnish from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips, 2x tabs Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
  10. Remove the screw securing the RH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x screw, 8mm, 2 Nm
  11. Remove the RH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  12. Remove the bolt that secures the RH corner of the rear fascia to the body,
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 10mm, 3.5 Nm
  13. Remove the rear fascia diffuser front bolts (x2)
    Informational PurposesAn informational icon, calling your attention
    Nota
    10mm, 5 Nm
  14. Release the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers
  15. Release the rear fascia assembly from the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Disengage locking tab, Recommend assistance, Place rear fascia on padded surface to avoid damage

Instalar

  1. Secure the rear fascia assembly onto the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Engage locking tab, Recommend assistance
  2. Secure the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers, Apply Loctite 222 onto bolts
  3. Install the rear fascia diffuser front bolts.
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts
  4. Install the bolt that secures the RH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 10mm, 3.5 Nm
  5. Install the RH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  6. Install the screw that secures the RH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x screw, 10mm, 2 Nm
  7. Install the RH rear fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips, 2x tabs, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  8. Raise the RH rear window.
  9. Close the RH rear door.
  10. Install the bolt that secures the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 10mm, 3.5 Nm
  11. Install the LH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  12. Install the screw that secures the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x screw, 8mm, 2 Nm
  13. Install the LH rear fender garnish to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips, 2x tabs, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  14. Return the 2nd row 60 seatback to vertical position.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Via trunk seat switch, Remove seatback protection if necessary
  15. Close the liftgate.
  16. Raise the LH rear window.
  17. Close the LH rear door.