2026-04-16

Brake Pads - Rear (Ceramic Brakes) (Remove and Replace)

Código de corrección 33010742 1.02 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Procedure

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  • 2026-01-22: Released new procedure.
  1. Prepare the vehicle for raising. See Elevación del vehículo - Elevador de 2 columnas.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Set air suspension to "Jack Mode".
  2. Open the LH front door and lower the window.
  3. Release the parking brake. See Pinza del freno de estacionamiento - Liberación.
  4. Remove the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  5. Place absorbent material underneath the brake reservoir area.
  6. Clean area around the brake fluid reservoir and remove the brake reservoir cap.
  7. Remove both rear wheels. See Conjunto de rueda (Desinstalación e instalación).
  8. Release the LH rear brake hose from the LH rear lower aft link.
  9. Remove and discard the LH rear brake pad retaining pins.
  10. Remove the bolts (x2) that attach the LH rear brake caliper to the knuckle.
  11. Remove the brake pads from the LH rear caliper.
  12. Push the pistons fully back into the LH rear brake caliper.
  13. Clean the LH rear brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Nota
    If necessary, only use a nylon brush.
  14. Remove the abutment pads (x2) from the LH rear brake caliper.
  15. Clean the abutment pads area on the LH rear brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use IPA wipe to clean the area, allow 1 minute dry time.
  16. Install new abutment pads (x2) to the LH rear brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Peel off the backing and install the pads with approximately 1 mm distance to the edge. Make sure the double sided tape mates onto the caliper.
  17. Apply tape on the friction surface of the new rear brake pads.
  18. Verify the position of the pads
    Informational PurposesAn informational icon, calling your attention
    Nota
    Note the position on the side of the pad. Position is described on the S/N of the floating clip-on shims of the pad and ending with "L" or "R". This step required due to removal of the floating clip-on shims in a later step
  19. Drill out the rear brake pad clips.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Drill the clips out with a 7 mm or 8 mm drill bit. Pay Attention to only drill the rivet till the head breaks free. Do not drill into the pad. Make sure to wear proper PPE.
  20. Clean debris off the rear brake pads.
  21. Remove and discard the floating clip-on shims from the rear brake pads.
  22. Remove the tape from the rear brake pads.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Clear any possible debris away with a blow gun.
  23. Clean the rear brake pads
    Informational PurposesAn informational icon, calling your attention
    Nota
    Clean the back side of the pads with IPA, allow 1 minute dry time.
  24. Install Sticky Shim Kit onto the rear brake pads.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Peel off the backing prior the installation. Center out the inner part of the pad and the rivets. Make sure that the double sided tape mates onto the brake pads.
  25. Position the rear brake pads into the LH rear brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Fold the tips of the backing. Ensure correct orientation of the pads (LH and RH). Verify correct orientation of the pads by alignment of the rivets to the piston. Do not fully press, do not apply any lubricant.
  26. Install the LH rear brake pad retaining pins.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Install new pins. Do not apply any lubricant.
  27. Install the rear brake pads to the LH rear brake caliper.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Peel off the backing. Verify that the Sticky Shim has not moved from the pads and push the pads into pistons. Verify flush attachment of the pad to the pistons (wrong pad orientation may cause contact of the rivet to the piston).
  28. Install the bolts that attach the LH rear brake caliper to the LH rear knuckle.
    135 Nm (99.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Nota
    Take care not to damage the brake disk!
  29. Install the bolt that attaches the LH rear brake hose to the LH rear lower aft link.
    6 Nm (4.4 lbs-ft)
  30. Install the LH rear wheel.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Start lug nuts by hand before using power tool.
  31. Repeat steps 8 to 30 on the rear RH side of the vehicle.
  32. Torque the LH and RH rear wheel nuts.
    175 Nm (129.1 lbs-ft)
  33. Install the LH and RH rear arachnid lug nut covers.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Align the cap with the valve stem.
  34. Pump the brake pedal a few times to ensure pedal feels normal.
  35. Check the brake fluid level and top off the reservoir as necessary.
  36. Install the brake reservoir cap.
  37. Remove the absorbent material from underneath the brake reservoir area.
  38. Install the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  39. Hold the brake pedal and select Park on the touchscreen to disable EPB service mode.
  40. Exit Service Mode. See Modo de servicio (Activación y desactivación).
  41. Burnish the brakes and verify proper brake pedal feel and performance.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Add correction code 33013010 as a separate activity to the Service Visit.