Código de corrección 17451012 0.48 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de que se lleva puesto el EPI adecuado al realizar el siguiente procedimiento.

1. Open LH front door
2. Lower LH front window
3. Press brake pedal to turn on drive rails
4. Set air suspension ride height to “Very High”
   Nota

   Using center display > Controls > Suspension > ''Very High''
5. Turn wheel fully to the right
6. Open hood
   Nota

   Via Center Display > Controls > Frunk Open
7. Remove rear underhood apron
   Nota

   8x clips

   

   

8. Remove LH underhood apron
   Nota

   10x clips

   

   

9. Remove RH underhood apron
   Nota

   10x clips

   

   

10. Remove front underhood apron
    Nota

    7x clips

    

    

11. Remove bolts securing fascia bracket to carrier
    Nota

    6x bolts, 10mm, 4 Nm

    

12. Remove push clips securing LH front wheel arch liner to fascia and move to the side for access
    Nota

    5x push clips, Shift bottom of liner down and flex top of liner against tire

    

    

    

13. Remove bolt securing front fascia to LH fender bracket
    Nota

    1x bolt, T25, 5 Nm

    

14. Press brake pedal to turn on drive rails

    

15. Turn wheel fully to the left

    

16. Remove push clips securing RH front wheel arch liner to fascia and move to the side for access
    Nota

    5x push clips, Shift bottom of liner down and flex top of liner against tire

    

    

    

17. Remove bolt securing front fascia to RH fender bracket
    Nota

    1x bolt, T25, 5 Nm

    

18. Power off vehicle from center display
    Nota

    Via Controls > Safety & Security > Power Off

    

19. Disconnect LV battery connector and First Responder Loop
    Nota

    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection

    

    

    

    

20. Disconnect front fascia harness
    Nota

    2x connectors, Pull red tab to disengage lock then disconnect, Located behind RH wheel arch liner

    

21. Release front fascia valance from front aero shield
    Nota

    3x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Do not remove 3x middle bolts

    

    

22. Release fascia from fender brackets and pull forward to remove from vehicle
    Nota

    Set fascia on protected surface, Recommend assistance

    

    

23. Disconnect battery backed siren connector
    Nota

    1x connector

    

24. Remove bolt securing battery backed siren to front bumper beam complete
    Nota

    1x bolt, 10mm, 8 Nm

    

    

25. Install bolt securing battery backed siren to front bumper beam complete
    Nota

    1x bolt, 10mm, 8 Nm

    

    

26. Connect battery backed siren connector
    Nota

    1x connector

    

27. Install front fascia onto vehicle and secure fascia to fender brackets
    Nota

    Recommend Assistance, Route fascia harness while installing, Verify front fascia valance sits under front aero shield before proceeding

    

    

28. Apply Loctite 222 to fasteners and secure front fascia valance to front aero shield
    Nota

    3x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Insert valance datums into aero shield holes, Do not remove 3x middle bolts

    

    

    

29. Connect front fascia harness
    Nota

    2x connectors, Engage locking tab, Located behind RH wheel arch liner

    

30. Install bolt securing fascia to RH fender bracket
    Nota

    1x bolt, T25, 5 Nm

    

31. Install push clips securing RH front wheel liner to fascia
    Nota

    5x push clips

    

    

32. Connect First Responder Loop and LV battery connector
    Nota

    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

    

33. Press brake pedal to turn on drive rails

    

34. Turn wheel fully to the right
35. Install bolt securing fascia to LH fender bracket
    Nota

    1x bolt, T25, 5 Nm

    

36. Install push clips securing LH front wheel liner to fascia
    Nota

    5x push clips

    

    

37. Install bolts securing fascia bracket to carrier
    Nota

    6x bolts, 10mm, 4 Nm

    

38. Install RH underhood apron
    Nota

    10x clips

    

    

39. Install LH underhood apron
    Nota

    10x clips

    

    

40. Install rear underhood apron
    Nota

    8x clips

    

    

41. Close hood
    Nota

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

42. Press brake pedal to turn on drive rails
43. Turn steering wheel back to center
44. Set air suspension ride height to “Medium”
    Nota

    Using center display, Controls > Suspension > ''Medium'
45. Close LH front door