2026-07-28

Coax Cable - Side Repeater - Front - LH (Overlay) (Remove and Replace)

Código de corrección 17403012 FRT 1.44 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  • 2026-07-09: Released new procedure.

Overlay

  1. Lower both front windows and open both front doors.
  2. Remove the cowl screen. See Panel - Pantalla de la cubierta (Desinstalación y sustitución).
  3. Remove fasteners securing LH V-brace and remove assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm
  4. Place wipers in service mode via UI
    Informational PurposesAn informational icon, calling your attention
    Nota
    Via Controls > Service > Wiper Service Mode, If wiper module is not in service mode then RH pivot arm will not clear V Brace crossmember
  5. Remove wiper module
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x bolts, 10mm, 8 Nm, 1x connector, Rotate module forward and up to access connector, Observe LH wiper arm pivot during removal to avoid damage to windshield, Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module, Do not attempt to test the module until it is fully installed in the vehicle
  6. Remove LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip, 2x tabs
  7. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips
  8. Remove LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, 2x magnets
  9. Move LH front seat backward
  10. Remove LH front floor mat
  11. Remove LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips
  12. Fold LH front cabin carpet aside for full access
  13. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip, 2x tabs
  14. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips, Partially release seal if needed
  15. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x magnets, 1x connector, 4x datums
  16. Move RH front seat backward
  17. Remove RH front floor mat
  18. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips
  19. Fold RH front cabin carpet aside for access
    Informational PurposesAn informational icon, calling your attention
    Nota
    Caution not to damage styrofoam of carpet
  20. Release harness from RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  21. Remove RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  22. Disconnect brown fakra connection from car computer
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, X836
  23. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  24. Remove LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lift every other spoke at a time until cap is released from rim
  25. Loosen LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  26. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Nota
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  27. Remove LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  28. Partially release rear portion of LH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x clips, 1x fan clip, Move liner aside
  29. Disconnect LH front repeater
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x connectors
  30. Release LH grommet from body
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
  31. Remove electrical tape securing harness bundle to rubber dust boot
  32. Remove the connector from the coax cable
    Informational PurposesAn informational icon, calling your attention
    Nota
    Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
  33. Apply harness tape onto LH coax overlay cable before installation
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  34. Position LH coax overlay cable into place, Place through LH wheel liner and dust boot towards interior cabin
    Informational PurposesAn informational icon, calling your attention
    Nota
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  35. Pull LH coax overlay cable through bulkhead and into interior cabin
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pull harness toward car computer under dashboard
  36. Position LH coax overlay cable onto main dash body harness, Secure cable onto harness using zip ties
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x zip-ties, Trim off excess material after harness has been secured
  37. Secure coax overlay through LH wheel liner and frunk harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x zip-ties, Trim off excess material after harness has been secured
  38. Depin the RH side coax cable (Terminal 1) from the connector X846
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  39. Insert coax overlay terminal into connector X846
  40. Remove the coax cable from the Connector X846
    Informational PurposesAn informational icon, calling your attention
    Nota
    Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
  41. Insert the connector locking tab and reconnect X846 together
  42. Connect brown fakra connection onto car computer
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, X836
  43. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    Cut the coax connector only
  44. Connect LH front repeater
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  45. Secure LH grommet onto body
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use electrical tape to wrap the end of the dust boot
  46. Secure rear portion of LH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x clips, 1x fan clip, Secure liner
  47. Install LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  48. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  49. Torque LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  50. Install LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    Align valve stem with cap
  51. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  52. Fold LH main carpet back into place
  53. Install LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips
  54. Install LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, 2x magnets
  55. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips, Verify weather seal is seated properly
  56. Install LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip, 2x tabs, Verify weather seal is seated properly
  57. Install LH front floor mat
  58. Move LH front seat to original position
  59. Install RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  60. Secure harness to RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  61. Fold RH main carpet back into place
    Informational PurposesAn informational icon, calling your attention
    Nota
    Caution not to damage styrofoam of carpet
  62. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips
  63. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x magnets, 4x datums, 1x connector
  64. Install RH front floor mat
  65. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips, Verify weather seal is seated properly
  66. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip, 2x tabs, Verify weather seal is seated properly
  67. Move RH front seat to original position
  68. Install wiper module
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x bolts, 10mm, 8 Nm, 1x connector, Secure electrical connector first, Rotate module rearward and under windshield, Observe LH wiper arm pivot during install to avoid damage to windshield, Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module, Do not attempt to test the module until it is fully installed in the vehicle
  69. Install fasteners securing LH V-brace and secure
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm
  70. Install the cowl screen. See Panel - Pantalla de la cubierta (Desinstalación y sustitución).
  71. Unlock the vehicle gateway. See Puerta de enlace (Desbloquear).
  72. Reset DAS on UI
    Informational PurposesAn informational icon, calling your attention
    Nota
    Select "Driver Assist" > "Cameras" > "Reset DAS", Ensure all cameras and reset DAS icon turn green on UI, If not you need to investigate further why a the particular DAS component is flagging red
  73. Ejecutar la rutina ODIN PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  74. Raise both front windows
  75. Close RH front door
  76. Close LH front door
    Informational PurposesAn informational icon, calling your attention
    Nota