2025-03-30

Harness - Ancillary - Front - LH (Remove and Replace)

Código de corrección 17107702 17107802 0.36 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.NOTA: Consulte Precauciones ergonómicas para ver prácticas de trabajo seguras.

  • 2025-03-24: Released new procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  1. Open LH front door
  2. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  3. Open hood
    Informational PurposesAn informational icon, calling your attention
    Nota
    Select Controls > Frunk Open
  4. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    8x clips
  5. Remove LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    10x clips
  6. Remove RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    10x clips
  7. Remove front underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips
  8. Remove frunk access panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips, 3x hooks, 1x connector
  9. Remove frunk carpet
  10. Remove frunk assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x bolts, 10mm, 5 Nm
  11. Disconnect active noise cancellation harness connector from frunk harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Release locking tab, 1x harness clip, Release clip securing active noise cancellation harness connector onto body
  12. Remove LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lift every other spoke at a time until cap is released from rim
  13. Loosen LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  14. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Nota
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  15. Remove LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  16. Release clips securing active noise cancellation harness onto bracket
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x harness clip
  17. Disconnect active noise cancellation harness connector from sensor and remove harness from vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connect, Release locking tab
  18. Connect active noise cancellation harness onto sensor
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connect, Secure locking tab
  19. Position active noise cancellation harness into place
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure the harness is routed above the lower links and below the tie rod and halfshaft
  20. Install clips securing active noise cancellation harness onto bracket
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x harness clip
  21. Install LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  22. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  23. Torque LH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  24. Install LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    Align valve stem with cap
  25. Connect active noise cancellation harness connector to frunk harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Secure locking tab, 1x harness clip, Install clip securing active noise cancellation harness connector onto body
  26. Install frunk assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x bolts, 10mm, 5 Nm
  27. Install frunk carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify carpet is properly seated under the seal
  28. Install frunk access panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips, 3x hooks, 1x connector
  29. Install front underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips
  30. Install RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    10x clips
  31. Install LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    10x clips
  32. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    8x clips
  33. Close hood
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  34. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  35. Close LH front door
    Informational PurposesAn informational icon, calling your attention
    Nota
    Close doors