Decor - Center Console (2025+) (Remove and Install)
Código de corrección
New
NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.
NOTA: Consulte Tiempos de tarifa plana (FRT) para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com.
NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.
NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.
- Open all four doors
- Lower both front windows
- Move LH front seat forward
- Move RH front seat forward
-
Release console back panel assembly
Nota7x clips, 6x datums
-
Remove console back panel assembly
Nota2x connectors, 2x Datums, Slide panel rearward to disengage from console assembly, Connector lock for lamp located underneath bracket, Connector may vary on build
-
Release LH and RH rear console carrier
Nota2x bolts, 10mm, 12 Nm
- Move LH front seat backward
- Move RH front seat backward
-
Release phone dock
Nota4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel
-
Remove phone dock
Nota3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage
-
Release IP service panel
Nota2x tabs, 4x datums, Release top tabs and slide rearward
-
Release diagnostic and CAN harnesses from IP service panel
Nota2x clips
-
Remove IP service panel
Nota1x connector
-
Remove LH front floor mat
-
Remove LH console side carpet
Nota11x clips
-
Release LH toeboard lower bracket from center console
Nota1x bolt, 10mm, 10 Nm
-
Remove RH front floor mat
-
Remove RH console side carpet
Nota11x clips
-
Release RH toeboard lower bracket from center console
Nota1x bolt, 10mm, 10 Nm
-
Release center console connectors to body harness
Nota4x connectors, 2x clips
-
Release LH and RH console carrier center bracket
Nota2x bolts, 10mm, 12 Nm
-
Remove console assembly
NotaLift at rear, rotate front from under IP and out passenger door, Take care not to scratch seats, IP or inner door panel, Recommend assistance if needed
-
Remove LH and RH console side panels
Nota17x clips each side
-
Release decor harness from console assembly
Nota6x connectors, 2x clips, 2x connectors wrapped in felt tape, Wrap connecters in felt tape after re-assembly, Connectors may very on build
-
Release decor from console assembly
Nota18x screws, T20, 1 Nm
-
Remove rear bright strip screws
Nota2x screws, T20, 1 Nm, Removal of screws allows flexibility to disengage decor bright
-
Remove console decor assembly
Nota6x datums, 1x connector, Lift up at front and slide out of rear bright strip
-
Install console decor assembly
Nota6x datums, 1x connector, Slide into rear bright strip and down into console assembly, Ensure all 6 datums engage and bright strip is aligned
-
Install rear bright strip screws
Nota2x screws, T20, 1 Nm, Confirm alignment of decor bright with rear bright trim
-
Secure decor to console assembly
Nota18x screws, T20, 1 Nm
-
Secure decor harness to console assembly
Nota6x connectors, 2x clips, 2x connectors wrapped in felt tape, Wrap connecters in felt tape after re-assembly, Connector may vary on build
-
Install LH and RH console side panels
Nota17x clips each side
-
Install console assemby
NotaCarefully maneuver front of assembly under and into IP carrier and lower rear into place, Recommend assistance if needed
-
Secure LH toeboard lower bracket to center console
Nota1x bolt, 10mm, 10 Nm
-
Secure RH toeboard lower bracket to center console
Nota1x bolt, 10mm, 10 Nm
-
Secure center console connectors to body harness
Nota4x connectors, 2x clips, Ensure all connector locks engaged
-
Secure LH and RH console carrier center bracket
Nota2x bolts, 10mm, 12 Nm
-
Install RH console side carpet
Nota11x clips
-
Install RH front floor mat
-
Install LH console side carpet
Nota11x clips
-
Install LH front floor mat
-
Secure IP service panel connector
Nota1x connector
-
Secure diagnostic and CAN harnesses to IP service panel
Nota2x clips
-
Secure IP service panel
Nota2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP
-
Install phone dock connections
Nota3x connectors, 1x clip
-
Install phone dock
Nota2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console
- Move LH front seat forward
- Move RH front seat forward
-
Secure LH and RH rear console carrier
Nota2x bolts, 10mm, 12 Nm
-
Install console back panel assembly
Nota2x connectors, 2x datums, Engage datums into console carrier slots, Connectors may vary on build
-
Secure console back panel assembly
Nota7x clips, 6x datums
- Close RH rear door
- Move RH front seat to original position
- Raise RH front window
- Close RH front door
- Move LH front seat to original position
- Raise LH front window
-
Close LH front door
NotaClose doors
- Close LH rear door