Clean Radiator (Maintenance)
Código de corrección 183010000.84 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de que se lleva puesto el EPI adecuado al realizar el siguiente procedimiento.
-
Open LH front door
-
Lower LH front window
-
Place vehicle in service mode via UI
NotaVia Controls > Software, Touch and hold "Model" for 2 seconds then release, Use screen keyboard to type "service" into dialog box and select OK button
-
Press brake pedal to turn on drive rails
-
Set air suspension ride height to “Very High”
NotaUsing center display > Controls > Suspension > ''Very High''
-
Turn wheel fully to the right
-
Open hood
NotaSelect Controls > Frunk Open
-
Remove rear underhood apron
Nota8x clips
-
Remove LH underhood apron
Nota10x clips
-
Remove RH underhood apron
Nota10x clips
-
Remove front underhood apron
Nota7x clips
-
Remove frunk access panel
Nota3x clips, 3x hooks, 1x connector
-
Remove frunk carpet
-
Remove frunk assembly
Nota4x bolts, 10mm, 5 Nm
-
Remove bolts securing fascia bracket to carrier
Nota6x bolts, 10mm, 4 Nm
-
Remove push clips securing LH front wheel arch liner to fascia and move to the side for access
Nota5x push clips, Shift bottom of liner down and flex top of liner against tire
-
Remove bolt securing front fascia to LH fender bracket
Nota1x bolt, T25, 5 Nm
-
Press brake pedal to turn on drive rails
-
Turn wheel fully to the left
-
Remove push clips securing RH front wheel arch liner to fascia and move to the side for access
Nota5x push clips, Shift bottom of liner down and flex top of liner against tire
-
Remove bolt securing front fascia to RH fender bracket
Nota1x bolt, T25, 5 Nm
-
Power off vehicle from center display
NotaVia Controls > Safety & Security > Power Off
-
Disconnect LV battery connector and First Responder Loop
Nota2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection
-
Disconnect front fascia harness
Nota2x connectors, Pull red tab to disengage lock then disconnect, Located behind RH wheel arch liner
-
Release front fascia valance from front aero shield
Nota8x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Do not remove 3x middle bolts
-
Release fascia from fender brackets and pull forward to remove from vehicle
NotaSet fascia on protected surface, Recommend assistance
-
Remove ankle catcher
Nota4x bolts, 10mm, 8 Nm, Number of bolts may vary on new vehicles
-
Disconnect active grille shutter actuator connector
Nota1x locking electrical connector
-
Release ambient temperature sensor grommet from active grille shutter
-
Disconnect ambient temperature sensor connector and route through grommet opening in shroud
Nota1x connector
-
Release locking tabs securing active grille shutter to cooling fan module assembly and remove active grille shutter through front of vehicle
Nota12x locking tabs, 2x clips
-
Remove plastic grille from the radiator
Nota9x locking tabs
-
Use shop-vac to clean dirt on the radiator
NotaIf necessary remove large debris
-
Use blow gun to clean dirt on the radiator again
NotaDo not get too close to the radiator blades
-
Install plastic grille to the radiator
Nota9x locking tabs
-
Install active grille shutter to cooling fan module assembly
Nota12x locking tabs, 2x clips, Align datums before engaging tabs, Make sure shutter slides inside tab not outside
-
Route ambient temperature sensor connector through grommet opening in shroud and install connector
Nota1x connector
-
Secure ambient temperature sensor grommet onto active grille shutter
-
Install active grille shutter actuator connector
Nota1x locking electrical connector, Engage locking tab
-
Install ankle catcher
Nota4x bolts, 10mm, 8 Nm, Number of bolts may vary on new vehicles
-
Install front fascia onto vehicle and secure fascia to fender brackets
NotaRecommend Assistance, Route fascia harness while installing, Verify front fascia valance sits under front aero shield before proceeding
-
Apply Loctite 222 to fasteners and secure front fascia valance to front aero shield
Nota8x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Insert valance datums into aero shield holes, Do not remove 3x middle bolts
-
Connect front fascia harness
Nota2x connectors, Engage locking tab, Located behind RH wheel arch liner
-
Install bolt securing fascia to RH fender bracket
Nota1x bolt, T25, 5 Nm
-
Install push clips securing RH front wheel liner to fascia
Nota5x push clips
-
Connect First Responder Loop and LV battery connector
Nota2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
-
Unlock Gateway
NotaPlace keycard on center console to turn on drive rails, hold down the brake pedal, while pressing right turn signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI adjacent to VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed adjacent to VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information
-
Perform Thermal Performance via Service UI
NotaSelect Thermal > Actions > Test Thermal Performance, click Run, close once routine is completed
-
Perform HVAC Performance via Service UI
NotaSelect Thermal > Actions > Test HVAC Performance, click Run, close once routine is completed
-
Exit Service mode
NotaPress and hold the Exit Service Mode button for 3 seconds
-
Press brake pedal to turn on drive rails
-
Turn wheel fully to the right
-
Install bolt securing fascia to LH fender bracket
Nota1x bolt, T25, 5 Nm
-
Install push clips securing LH front wheel liner to fascia
Nota5x push clips
-
Install bolts securing fascia bracket to carrier
Nota6x bolts, 10mm, 4 Nm
-
Install frunk assembly
Nota4x bolts, 10mm, 5 Nm
-
Install frunk carpet
NotaVerify carpet is properly seated under the seal
-
Install frunk access panel
Nota3x clips, 3x hooks, 1x connector
-
Install front underhood apron
Nota7x clips
-
Install RH underhood apron
Nota10x clips
-
Install LH underhood apron
Nota10x clips
-
Install rear underhood apron
Nota8x clips
-
Close hood
NotaPress firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
-
Press brake pedal to turn on drive rails
-
Turn steering wheel back to center
-
Raise LH front window
-
Close LH front door
NotaClose doors