2025-06-17

Discos de freno - Parte trasera - Juego (Desinstalación y sustitución)

Código de corrección 33011402 0.42 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de que lleva puesto el EPI adecuado al realizar el siguiente procedimiento.

  • 2025-05-08: Added brake pad burnishing step to be performed after rotor replacement.
  • 2024-06-04: Updated EPB Service Mode reference.
  • 2023-11-09: Updated rear caliper to knuckle torque to 115 Nm.
  • 2023-10-25: Updated EPB Service Mode reference.
  • 2023-10-16: Added step to make sure caliper piston face is aligned for Mando calipers.

Retirar

  1. Raise and support the vehicle. See Elevación del vehículo - Elevador de 2 columnas.
  2. Remove both rear wheels. See Conjunto de rueda (Desinstalación e instalación).
  3. Coloque el vehículo en el Modo de servicio del EPB. Consulte Pinza del freno de estacionamiento - Liberación.
  4. Disconnect the EPB harness connector from the LH caliper motor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Presione la pestaña de bloqueo roja del conector para acoplar el mecanismo de bloqueo. NO presione ni tire hacia arriba de la pestaña de bloqueo roja.
  5. Remove the bolts that attach the LH rear brake caliper to the LH rear knuckle and hang the caliper from the body of the vehicle using an S-hook.
  6. Si está instalado, retire y deseche el perno que fija el rotor del freno al buje.
    Informational PurposesAn informational icon, calling your attention
    Nota
    No se instalará un perno nuevo.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 13 mm
  7. Repeat step 4 through step 6 for the RH side of the vehicle.

Instalar

  1. Position the LH front rotor to the knuckle assembly.
    Informational PurposesAn informational icon, calling your attention
    Nota
    It is not necessary to install the bolt that attaches the rotor to the hub.
    Figura 1. LH shown; RH similar
  2. If a Mando caliper, perform these additional substeps.
    1. Remove the brake pads from the caliper.
    2. Use needle-nose pliers to ensure that the slots in the rear brake caliper piston face are at the 12 o'clock and 6 o'clock positions.
    3. Install the brake pads into the caliper.
  3. Remove the S-hook and install the bolts that attach the LH rear brake caliper to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, E18, 115 Nm
  4. Connect the LH EPB caliper harness connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Inserte la pestaña de bloqueo roja en el conector para acoplar el bloqueo del conector.
  5. Repeat steps 1 and 4 for the RH side of the vehicle.
  6. Hold the brake pedal and select "Park" on the touchscreen to disable the EPB service mode.
  7. Install both rear wheels. See Conjunto de rueda (Desinstalación e instalación).
  8. Lower the vehicle.
  9. Asiente los frenos. Consulte Pastillas de freno - Pulido.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Durante la conducción del vehículo, asegúrese de que el tacto y el rendimiento del pedal de freno sean correctos.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Añada el código de corrección para el pulido de las pastillas de freno 33013000 como una actividad independiente a la visita de servicio.