24/08/2023 10:48:54

Manguera - Entrada - Inversor - Unidad de tracción trasera (4DU) (Desinstalación y sustitución)

Código de corrección 18301732 0.54 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

  • 2023-08-14: Added a note about vacuum refill requirement when the coolant loss is greater than 1L.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento es PRELIMINAR, aunque ya ha sido validado. Es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.

Retirar

  1. Move the vehicle to a 2 post lift. See Elevación del vehículo - Elevador de 2 columnas.
  2. Enable Service Mode on the touchscreen. See Modo de servicio.
  3. Remove the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  4. Remove the cabin intake duct. See Conducto - Entrada de la cabina (Desinstalación y sustitución).
  5. Disconnect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).
  6. Remove the mid aero shield panel. See Panel - Deflector aerodinámico - Central (Desinstalación y sustitución).
  7. Release the clips (x4) that attach the coolant hoses to the rear skid plate.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Clip quantity varies with older vehicles.
  8. Remove the HV battery rear skid plate. See Placa de deslizamiento - Batería de alta tensión - Parte trasera (Desinstalación y sustitución).
  9. Position a coolant drain collector underneath the LH rear of the HV battery.
  10. Release the clip, disconnect the rear drive unit inverter inlet hose from the HV battery, and then immediately plug both fittings.
  11. Release the clip, disconnect the rear drive unit inverter inlet hose from the rear drive unit inverter, and then immediately plug both fittings.
  12. Release the clip that attaches the rear drive unit inverter inlet hose from rear drive unit HV harness.
  13. Remove the rear drive unit inverter inlet hose down and out from between the rear subframe and the HV battery.

Instalar

  1. Install the rear drive unit inverter inlet hose in and up between the rear subframe and the HV battery.
  2. Fasten the clip that attaches the rear drive unit inverter inlet hose to rear drive unit HV harness.
  3. Remove the plugs from the fittings, immediately connect the rear drive unit inverter inlet hose to the rear drive unit inverter, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  4. Remove the plugs from the fittings, immediately connect the rear drive unit inverter inlet hose to the HV battery and fasten the clip.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Perform a push-pull-push test to make sure that the hose is fully secured. Coolant loss greater than 1L requires vacuum fill.
  5. Remove the coolant drain collector from under the vehicle.
  6. Install the HV battery rear skid plate. See Placa de deslizamiento - Batería de alta tensión - Parte trasera (Desinstalación y sustitución).
  7. Fasten the clips (x4) that attach the coolant hoses to the rear skid plate.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Clip quantity varies with older vehicles.
  8. Install the mid aero shield panel. See Panel - Deflector aerodinámico - Central (Desinstalación y sustitución).
  9. Connect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).
  10. On the touchscreen, touch the wrench icon > Diagnostics > Thermal.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Alternatively, touch Controls (vehicle icon) > Service Mode > Diagnostics > Thermal.
  11. Hold up on the turn signal stalk, and then press and hold the brake pedal at the same time for 10 seconds to authorize.
  12. On the touchscreen, touch START to the left of “Start Coolant Air Purge” and wait for the task to complete (10 minutes).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Alternatively, touch START to the left of “Start Coolant Air Purge”, touch RUN TASK, wait for the task to complete (10 minutes), then touch X in the upper left corner.
  13. Add coolant to the reservoir as necessary, and install the reservoir cap.
  14. Install the cabin intake duct. See Conducto - Entrada de la cabina (Desinstalación y sustitución).
  15. Install the rear underhood apron. See Faldón del vano del motor - Parte trasera (Desinstalación y sustitución).
  16. Disable Service Mode. See Modo de servicio.
  17. Remove the vehicle from the 2 post lift. See Elevación del vehículo - Elevador de 2 columnas.