15/04/2024 09:43:38

Consola del techo - Parte delantera (sin botón de llamada de emergencia) (EMEA) (Retroadaptación)

Código de corrección 15202306 0.36 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.0.10

  • 2023-10-20: Updated steps to change Gateway configuration using Toolbox 3.
This procedure describes the replacement of the Front Overhead Console (FOHC) with physical e-Call button on the FOHC by a FOHC without the physical e-Call button on the FOHC. After replacing the FOHC, the vehicle configuration parameters must be updated to ensure that the e-Call functionality becomes available via the touchscreen.

Procedure

  1. Open the LH front door and lower the window.
  2. Put the vehicle in service mode through the touchscreen. See Modo de servicio.
  3. Disconnect 12V power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).
  4. Remove the front overhead console. See Consola del techo - Parte delantera (Desinstalación y sustitución).
  5. Pull the FOHC connector (X299) outwards for access
  6. Remove 2 - 4 cm of the electrical tape from the harness.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Take care not to damage the wires while using a blade to remove the tape.
  7. Release the locking clips from the connector
  8. Remove pin 6 (X299-6) from the connector
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use the pin drag kit to release the locking tab, then pull out the wire.
  9. Cut off the terminal from the removed wire.
  10. Apply heat shrink tube to the cut wire end, and then apply heat to prevent the wire from making contact.
  11. Remove pin 12 (X299-12) from the electrical connector, and then repeat steps 9and 10.
  12. Remove pin 14 (X299-14) from the electrical connector, and then repeat steps 9 and 10.
  13. Remove pin 15 (X299-15) from the electrical connector, and then repeat steps 9 and 10.
  14. Remove pin 16 (X299-16) from the electrical connector, and then repeat steps 9 and 10.
  15. Use electrical tape to attach the removed wires from connector X299 to the FOHC harness.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use the yellow electrical tape in the kit to denote a rework has been performed.
  16. Install the front overhead console assembly to the headliner. See Consola del techo - Parte delantera (Desinstalación y sustitución).
  17. Connect 12V power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).
  18. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Conexión y desconexión).
  19. Usie Toolbox 3 to change the configuration value for eCallEnabled to enabled_ui_sos. See Configuración de la puerta de enlace (visualización y modificación).
  20. On the touchscreen, touch Controls > Safety and make sure that the SOS shortcut button (1) and the SOS EMERGENCY CALL button (2) are available on the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The SOS shortcut button (1) takes the user directly to the Safety and Security tab, the SOS EMERGENCY CALL button (2) makes the actual call when touched.
  21. Using toolbox 3:
    1. Select the Actions tab, and then type "VFOHC" in the search field.
    2. Run the ODIN routine TEST-SELF_VCLEFT_X_VFOHCSearch for routine in Toolbox and allow the routine to complete.
    3. Disconnect the laptop from the vehicle.
  22. Reinstall the vehicle firmware. See Reinstalación de software - Pantalla táctil.
  23. Exit Service Mode. See Modo de servicio.
  24. Inform the customer why the e-Call functionality has changed after the headliner retrofit and instruct them how to use the touchscreen to make an emergency call.