21/12/2022 09:05:46
Mazo de cables - Filtro - Antena - Lado derecho (Desinstalación y sustitución)
Código de corrección 17108402 0.25 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.
Retirar
-
Open all the doors and fully lower all the windows.
NotaIf the vehicle is being powered down, latch the rear doors to prevent accidental closure.
- Move the LH and RH front seats fully forward.
- Remove the LH 2nd row seat side bolster. See Refuerzo - Lateral - Asiento - 2.ª fila - Lado izquierdo (Desinstalación y sustitución).
- Remove the LH side rail trim. See Guarnecido - Raíl lateral - Lado izquierdo (Desinstalación y sustitución).
- Remove the LH upper C-pillar trim. See Guarnecido - Pilar C - Superior - Lado izquierdo (Desinstalación y sustitución).
-
Release the clip and tabs (x4) that attach the LH rear C-pillar trim to the body, and then set the trim aside.
NotaPull the rear of the trim forward, and then upward to remove it.Consejo: Se recomienda utilizar las siguientes herramientas:
- Plastic trim tool
- Remove the RH 2nd row seat side bolster. See Refuerzo - Lateral - Asiento - 2.ª fila - Lado izquierdo (Desinstalación y sustitución).
- Remove the RH side rail trim. See Guarnecido - Raíl lateral - Lado izquierdo (Desinstalación y sustitución).
- Remove the RH upper C-pillar trim. See Guarnecido - Pilar C - Superior - Lado izquierdo (Desinstalación y sustitución).
-
Release the clip and tabs (x4) that attach the RH rear C-pillar trim to the body, and then set the trim aside.
NotaPull the rear of the trim forward, and then upward to remove it.Consejo: Se recomienda utilizar las siguientes herramientas:
- Plastic trim tool
- Remove the package tray trim. See Guarnecido - Bandeja de paquetes (Desinstalación y sustitución).
-
Disconnect the RH antenna filter harness connector from the tuner.
Consejo: Se recomienda utilizar las siguientes herramientas:
- Small flat head screwdriver
-
Disconnect the RH antenna filter harness connector from the tuner and body harness.
Consejo: Se recomienda utilizar las siguientes herramientas:
- Small flat head screwdriver
-
Release the clip that attaches the RH antenna filter harness to the body.
Consejo: Se recomienda utilizar las siguientes herramientas:
- Herramienta de retirada de clips con palanca
-
Remove the RH antenna filter harness from the backlight glass.
NotaPeel the tape back found at each end of harness housing seal.Consejo: Se recomienda utilizar las siguientes herramientas:
- Plastic trim tool
-
Disconnect the RH antenna filter harness connector from the heater grid, and then remove the harness from the vehicle.
PRECAUCIÓNGently disconnect the harness. Do not damage the heater grid.Consejo: Se recomienda utilizar las siguientes herramientas:
- Ganzúa en miniatura de mango blando, punta de 90 grados, 6 pulg.
Instalar
-
Position the RH antenna filter harness on the vehicle, and then connect the harness connector to the heater grid.
-
Install the clip that attaches the RH antenna filter harness to the body.
-
Connect the RH antenna filter harness connector to the tuner and body harness.
-
Connect the RH antenna filter harness connector to the tuner.
-
Install the RH antenna filter harness on the backlight glass.
NotaApply a small piece of tape at each end of the seal clip.Consejo: Se recomienda utilizar las siguientes herramientas:
- Felt tape
- Scissors
- Install the package tray trim. See Guarnecido - Bandeja de paquetes (Desinstalación y sustitución).
-
Install the clip and tabs (x4) that attach the LH rear C-pillar trim to the body.
NotaSlide the back tabs into package tray, and then push the front tabs toward the rear.
- Install the LH upper C-pillar trim. See Guarnecido - Pilar C - Superior - Lado izquierdo (Desinstalación y sustitución).
- Install the LH side rail trim. See Guarnecido - Raíl lateral - Lado izquierdo (Desinstalación y sustitución).
- Install the LH 2nd row seat side bolster. See Refuerzo - Lateral - Asiento - 2.ª fila - Lado izquierdo (Desinstalación y sustitución).
- Raise the LH 2nd row seat.
- Repeat step 7 through step 11 for the RH side of the vehicle.
- Move the LH and RH front seats to the original positions.
- Raise all the windows and close all the doors.