2024-12-10

Manguera - Derivación del tren de transmisión de la unidad de tracción delantera (bomba de calor) (tracción a las ruedas traseras) (Desinstalación y sustitución)

Código de corrección 18302302 0.55 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.

Retirar

  1. Raise and support vehicle
  2. Open LH front door
  3. Lower LH front window
  4. Open hood
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press "Open" button on touchscreen to release latch, Lift lid manually
  5. Remove rear apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    12x clips, Only store rear apron visible face upwards
  6. Remove cabin intake upper duct assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips, Some configurations may come with 4x clips
  7. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Nota
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  8. Disconnect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x nut, 10mm, 6 Nm, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
  9. Disconnect first responder loop
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Release locking tab
  10. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Nota
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Verify doors are clear of surrounding objects
  11. Remove outer fasteners securing front aero shield
    Informational PurposesAn informational icon, calling your attention
    Nota
    9x bolts, 10mm, 5 Nm
  12. Remove remaining nuts and remove front aero shield from vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x nuts, 15mm, 5 Nm
  13. Remove clips securing RH front wheel liner to vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x clips
  14. Use bungee strap to pull back RH front wheel liner
    Informational PurposesAn informational icon, calling your attention
    Nota
    Secure to subframe
  15. Position coolant drain container underneath RH front of HV battery
  16. Disconnect PT return tube from FDU bypass hose
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x clips, 2x plugs, Lower hose located on RH front of HV battery, Plug both hose ends
  17. Remove coolant drain container from underneath vehicle

Instalar

  1. Release FDU bypass hose from front subframe
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x fir tree clip
  2. Lower vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  3. Position fluid catcher underneath front of vehicle
  4. Disconnect FDU bypass hose from the Supermanifold and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x spring clip, 2x plugs, Plug supermanifold and bypass hose to prevent excess coolant drain
  5. Feed hose into position and install FDU bypass hose to the supermanifold
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x spring clip, 2x plugs, Install plug onto lower end of hose to avoid coolant loss, Remove plug from Supermanifold, Perform push-pull-push test to make sure hose is fully engaged
  6. Remove fluid catcher from underneath vehicle
  7. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Nota
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  8. Secure FDU bypass hose to front subframe
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x fir tree clip
  9. Position coolant drain container underneath RH front of HV battery
  10. Remove plugs then connect PT return tube to FDU bypass hose
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x clips, 2x plugs, Perform push-pull-push test to make sure hoses are fully engaged
  11. Remove coolant drain container from underneath vehicle
  12. Release RH front wheel liner from bungee strap
    Informational PurposesAn informational icon, calling your attention
    Nota
    Remove strap from vehicle
  13. Install clips securing RH front wheel liner to vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x clips
  14. Position front aero shield to vehicle and install nuts
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x nuts, 15mm, 5 Nm
  15. Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield
    Informational PurposesAn informational icon, calling your attention
    Nota
    9x bolts, 10mm, 5 Nm
  16. Lower vehicle fully
    Informational PurposesAn informational icon, calling your attention
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  17. Install frunk assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Nota
    12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles. Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam
  18. Install bolts securing frunk assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x bolts, 10mm, 5 Nm, Lower RBN covers after installing upper fasteners, Newer vehicles may not be equipped with covers
  19. Install frunk close out panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
  20. Remove coolant bottle cap
  21. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure that fluid level is at Max line
  22. Connect first responder loop
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Engage locking tab, Connect FRL before connecting 12V to avoid damage to car computer
  23. Connect 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x nut, 10mm, 6 Nm
  24. Realice la siguiente rutina a través del modo de servicio o Toolbox (consulte 0005 - Modos de servicio): TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete
  25. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure that fluid level is at Max line
  26. Install coolant bottle cap
  27. Install cabin intake upper duct assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips, Some configurations may come with 4x clips
  28. Install rear apron
    Informational PurposesAn informational icon, calling your attention
    Nota
    12x clips
  29. Close hood
  30. Raise LH front window
  31. Close LH front door
  32. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lower rack arms fully and remove from under vehicle