2026-08-09

Conjunto de la puerta - Puerto de carga (global) (desinstalación y sustitución)

Código de corrección 44011512 1.68 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT asociado reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de que se lleva puesto el EPI adecuado al realizar el siguiente procedimiento.

  • 2025-10-21: Added links to sub-procedures. Added steps to measure old charge port door and adjust new one to old door measurements if needed.

Retirar

  1. Remove the rear sill panel. See Guarnecido - Panel del larguero - Parte trasera - Lado izquierdo (Desinstalación y sustitución).
  2. Open the charge port door.
  3. Open the liftgate.
  4. Extraiga el soporte del guarnecido lateral del maletero. Consulte:
  5. Retire el cojín del asiento de 3.ª fila, si está instalado. Consulte Cojín - Asiento - 3.ª fila (Desinstalación y sustitución).
  6. Disconnect LV power. See Alimentación de baja tensión (Desconexión y conexión).
  7. Verify that high voltage is no longer available to the charge port. See Comprobación de la tensión del puerto de carga.
  8. Remove the LH inner reinforcement. See Refuerzo - Interior - Lado izquierdo (Desinstalación y sustitución).
  9. Disconnect the LH tail lamp connector.
    Nota
    Release the red locking tab.
  10. Remove the nuts (x2) that secure the LH tail lamp to the body.
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 8 mm
    Consejo
    Be careful not to drop the fasteners into the vehicle body.
  11. Remove the LH body tail lamp from the vehicle.
    Nota
    2x datums, Note one datum clips into charge port door assembly
  12. Release the charge port latch connection.
    Nota
    Take note of the harness routing.
    Nota
    Pull the red locking tab outwards to release lock, then pull again to release connector.
  13. Release the charge port connection.
    Nota
    Carefully remove the white locking tab, depress the tab to release the connection from the charge port, then pull the connector out.
    Nota
    The connection is intended to disengage the safety cap when released.
  14. Remove the charge port safety cap.
  15. Remove the nuts (x2) that secure the charge port busbar to the charge port. Remove the busbar leads from the studs.
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 11 mm
    Nota
    The nuts have captive washers. Take caution of any tension present with the busbar
    PRECAUCIÓN
    The busbar may be under tension. Use caution to avoid damage upon removal.
  16. Remove the bolts (x4) that secure the charge port assembly, then remove the assembly.
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  17. Release the charge port door connection from the charge port ECU.
    Nota
    Take note of the original routing.
  18. Release charge port door harness grommet from body and feed the harness out.
  19. Remove the bolt that secures the charge port door to vehicle body.
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 8 mm
  20. Remove the charge port door from the vehicle.
    Nota
    3x datums, Release single datum from vehicle body, Maneuver door assembly and motor out from rear of vehicle, Guide harness out
  21. If the charge port door was properly aligned, measure and note the adjustable mounting point settings.

Instalar

  1. If the previous charge port door was properly aligned and measurements are available, set the new charge port door's adjustable mounting points to those settings.
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Hexagonal de 5 mm
  2. Install the charge port door onto the vehicle.
    Nota
    Guide the harness in, maneuver the door assembly and motor in from the rear of the vehicle, then secure the single datum into the body.
  3. Install the bolt that secures the charge port door to vehicle body.
    1 Nm (.7 lbs-ft)
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Hexagonal de 8 mm
  4. Secure the charge port door harness grommet onto the body.
  5. Secure the charge port door connection onto the charge port ECU.
    Nota
    Return to original routing
  6. Install the charge port assembly into vehicle and torque the bolts (x4).
    7 Nm (5.2 lbs-ft)
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    Nota
    New charge ports come pre-applied with Penetrox.
  7. Clean charge port assembly busbar contact surface of residual penetrox
    Nota
    Use plastic trim tool to push IPA wipe down between plastic divider, Allow 1 minute dry time
  8. Clean the busbar lead contact surfaces with isopropyl alcohol to remove any residual Penetrox.
    Nota
    Allow 1 minute for IPA to dry.
  9. Apply Penetrox to the backside of the busbar leads.
    Nota
    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads. Spread evenly to verify the contact surface is fully covered
  10. Install the charge port busbar leads to the charge port assembly. Torque the nuts (x2).
    9 Nm (6.6 lbs-ft)
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 11 mm
    Nota
    The nuts have captive washers.
    PRECAUCIÓN
    If excessive force is required to seat busbars, they may have been bent. Inspect for damage and replace if necessary.
  11. Inspect HV insulating gloves
    Nota
    Check gloves for damage prior to use, Refer to service document TN-15-92-003, for information on inspecting HV gloves. https://service.teslamotors.com/documents?model=&keys=TN-15-92-003&vehicle_system=&sort_by=field_date_submitted&sort_order=DESC
  12. Put on HV insulating gloves and leather over gloves
  13. Perform Hioki resistance test at each HV joint (x2) from the HV busbar lead to charge port stud.
    • If the resistance is greater than 0.270 mΩ (270 μΩ), remove the fastener, clean the areas with isopropyl alcohol, install fastener back, and retest.
    • If the resistance is less than 0.050 mΩ (50 μΩ), reposition the probe and measure again. If the measurement is under 0.050 mΩ again, proceed to the next step.
  14. Remove leather over gloves and HV insulating gloves
  15. Install the charge port safety cap.
    Nota
    Engage hooks (x2). The safety cap clicks into position.
  16. Secure the charge port connection.
    Nota
    Fully engage the connection and the white locking tab.
  17. Secure the charge port latch connection.
    Nota
    Return harness to original routing. The harness sits in front of the busbar. Fully engage the connector and red locking tab.
  18. Install the LH body tail lamp onto the vehicle.
    Nota
    One datum clips into charge port door assembly.
  19. Install the nuts (x2) that secure the LH tail lamp to the body.
    3.5 Nm (2.6 lbs-ft)
    Consejo
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 8 mm
    PRECAUCIÓN
    Be careful not to drop the fasteners into the vehicle body.
  20. Connect the LH tail lamp connector.
    Nota
    Engage the red locking tab.
  21. Install the LH inner reinforcement to the body, and then install the bolts (x10) that attach the reinforcement to the body.
    27 Nm (19.9 lbs-ft)
    Nota
    The bottom two bolts require improvising an 8 mm ratchet box-end wrench to turn the T40 socket.
  22. Install the 3rd row seat cushion, if previously removed. See Cojín - Asiento - 3.ª fila (Desinstalación y sustitución).
  23. Reconnect LV power. See Alimentación de baja tensión (Desconexión y conexión)
  24. Charge the vehicle to verify correct operation of the charging system.
  25. Close the charge port door.
  26. Fold LH 3rd row seat back into down position
  27. Install the trunk side trim bracket. See:
  28. Move the seats back to their original positions.
  29. Install the rear sill panel. See Guarnecido - Panel del larguero - Parte trasera - Lado izquierdo (Desinstalación y sustitución).
  30. Calibrate the LH and RH falcon wing doors.
    Nota
    Hold the upper B-pillar button in the down position to manually calibrate.
  31. Move the LH front seat to its original position.