2026-07-28

Coax Cable - Side Repeater - Front - RH (Overlay) (Remove and Replace)

Código de corrección 17403112 FRT 2.82 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  • 2026-07-09: Released new procedure.

Overlay

  1. Open both front doors and lower both front windows.
  2. Remove the underhood storage unit. See Unidad de almacenamiento del vano del motor (Desinstalación e instalación).
  3. Remove the wiper module. See Módulo del limpiaparabrisas (Desinstalación y sustitución).
  4. Move the RH front seat backward.
  5. Remove RH front floor mat
  6. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x magnets, 1x connector, 4x datums
  7. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips, 2x datums
  8. Remove RH front door sill trim panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    8x clips, 3x datums, Partially release seal if needed
  9. Remove RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips
  10. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
  11. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, T25, 5 Nm, 2x clips, 1x datum
  12. Fold RH front cabin carpet aside for access
  13. Release harness from RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  14. Release RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 5 Nm, 2x nuts, 10mm, 5 Nm
  15. Remove RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    Fold RH primary support carpet up, Rotate RH footrest panel out of vehicle
  16. Disconnect side repeater cameras connector X870 at car computer
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Release red tab then disconnect
  17. Raise and support the vehicle.
  18. Remove RH front wheel center cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x cap
  19. Loosen RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  20. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Nota
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  21. Remove RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  22. Release rear portion of RH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips, 2x tabs, Starting from the rear release garnish to access rocker
  23. Remove rear portion of RH front wheel liner
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x clips, 1x fan clip, Carefully rest rear portion of wheel line on brake rotor
  24. Disconnect RH front repeater
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x connectors
  25. Release RH grommet from body
    Informational PurposesAn informational icon, calling your attention
    Nota
    With a razor blade, carefully cut the electrical tape away exposing the rubber dust boot
  26. Remove electrical tape securing harness bundle to rubber dust boot
  27. Release the terminal 2 lock on the double connector side of coax overlay cable
    Informational PurposesAn informational icon, calling your attention
    Nota
    Using the pin drag kit, carefully lift the hold down tab
  28. Remove the double connector from the overlay coax cable
    Informational PurposesAn informational icon, calling your attention
    Nota
    Using the pin drag kit, pull the coax away from the connector
  29. Wrap the overlay coax cable with harness tape before installation
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is installed the vehicle
  30. Feed the previously removed coax terminal through the RH wheel liner and dust boot towards the interior cabin
    Informational PurposesAn informational icon, calling your attention
    Nota
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  31. Pull the RH coax over through the bulkhead and into the interior cabin
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pull harness toward car behind car computer
  32. Overlay the RH coax wire onto the harness and secure it to the car computer harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x zip-ties, Trim off excess material after harness has been secured
  33. Secure coax overlay through RH wheel liner and frunk harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x zip-ties, Trim off excess material after harness has been secured
  34. Depin the LH side coax cable (Terminal 2) from the connector X820
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify that you are removing the correct side (1 & 2, where 1 is the LH repeater and 2 is the RH repeater) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  35. Remove the coax cable from the connector X820
    Informational PurposesAn informational icon, calling your attention
    Nota
    Using the pin drag kit, carefully lift the hold down tab an simultaneously pull the coax away from the connector
  36. Insert the connector locking tab and reconnect X820 together
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector
  37. Secure side repeater cameras connector X870 onto car computer
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector
  38. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    Nota
    Cut the coax connector only
  39. Connect RH front repeater
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  40. Secure RH grommet onto body
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use electrical tape to wrap the end of the dust boot
  41. Secure rear portion of RH front wheel liner
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x clips
  42. Secure rear portion of RH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips, 2x tabs, Fully secure and carefully engage clips
  43. Install RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  44. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  45. Torque RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x nuts, 21mm, 175 Nm
  46. Install RH front wheel center cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x cap, Verify emblem is aligned with valve stem
  47. Install RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    Rotate RH footrest panel onto vehicle, Fold RH primary support carpet down
  48. Secure RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 5 Nm, 2x nuts, 10mm, 5 Nm
  49. Secure harness to RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip
  50. Fold RH main carpet back into place
  51. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x magnets, 4x datums, 1x connector
  52. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, T25, 5 Nm, 2x clips, 1x datum
  53. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x clips, 3x datums, Verify weather seal is seated properly
  54. Install RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x clips
  55. Install RH front door sill trim panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    8x clips, 3x datums, Verify seal is seated properly
  56. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x clips, 2x datums
  57. Install RH front floor mat
  58. Install the wiper module. See Módulo del limpiaparabrisas (Desinstalación y sustitución).
  59. Install the underhood storage unit. See Unidad de almacenamiento del vano del motor (Desinstalación e instalación).
  60. Press brake pedal to turn on drive rails
  61. Turn steering wheel back to center
  62. Set air suspension ride height to “Medium”
    Informational PurposesAn informational icon, calling your attention
    Nota
    Using center display, Controls > Suspension > ''Medium'
  63. Activate Service Mode using the touchscreen.
  64. Unlock Gateway
    Informational PurposesAn informational icon, calling your attention
    Nota
    After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information
  65. Reset DAS via Service UI
    Informational PurposesAn informational icon, calling your attention
    Nota
    In Service mode navigate to Driver Assist > Cameras > Reset DAS
  66. Ejecutar la rutina ODIN PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  67. Raise both front windows.
  68. Close the LH front door.
  69. Vehicle will need to be driven by customer to complete the calibration procedure. During this time DAS functions will be completely unavailable