2026-03-12

Steering Gear (RHD) (Model Y L) (Remove and Install)

Correction code NEW FRT 1.62 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-03-12: Released new procedure.

Remove

  1. Open the RH front door and lower the RH front window.
  2. Remove the front wheel caps. See Cap - Wheel (Model YL) (Remove and Replace).
  3. Remove the front wheels. See Wheel Assembly (Remove and Install).
  4. Remove the RH outer tie rod end. See Tie Rod Outer - LH (Remove and Replace).
  5. Remove the cooling fan module assembly. See Cooling Fan Module (Remove and Replace).
  6. Remove and discard the bolt that attaches the steering column to the steering gear assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 3/8" DR, SWIVEL, 13MM
    Informational PurposesAn informational icon, calling your attention
    Note
    If need, turn the steering wheel slightly to ensure that the bolt is in a convenient position for removal, then use a magnetic pickup tool to assist in removing the bolt.
  7. Turn the steering wheel to the leftmost position and secure it using a steering wheel level to ensure it remains horizontal and cannot rotate freely.
  8. Slide the steering column upward to disconnect it from the steering gear assembly.
  9. Release the locking tabs and disconnect the upper steering gear connectors (x2).
  10. Release the locking tabs and disconnect the lower steering gear connectors (x2).
  11. Move the steering harness aside.
  12. Disconnect the front subframe harness connector.
  13. Release the clip that attaches the radiator inlet hose to the LH front rail harness bracket.
  14. Release the clips (x2) that attach the main front harness bracket to the LH front rail.
  15. Remove the inner bolts (x2) that attach the steering gear assembly to the front subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 3/8" DR, SWIVEL, 18MM
  16. Remove the outer bolts (x2) that attach the steering gear assembly to the front subframe.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT 3/8" DR, SHALLOW, 15MM
  17. Slide the steering gear assembly to the LH side of the steering gear assembly, then maneuver the RH side upward to remove it from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not damage any components.

Install

  1. Install the steering gear into the vehicle.
  2. Loosely install the bolts (x4) that attach the steering gear assembly to the front subframe.
  3. Torque the inner bolts (x2) that attach the steering gear assembly to the front subframe.
    75 Nm (55.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 3/8" DR, SWIVEL, 18MM
  4. Torque the outer bolts (x2) that attach the steering gear assembly to the front subframe.
    47 Nm (34.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT 3/8" DR, SHALLOW, 15MM
  5. Secure the clips (x2) that attach the main front harness bracket to the LH front rail.
  6. Secure the clip that attaches the radiator inlet hose to the LH front rail harness bracket.
  7. Connect the front subframe harness connector.
  8. Engage the locking tabs and connect the upper steering gear connectors (x2).
  9. Engage the locking tabs and connect the lower steering gear connectors (x2).
  10. Slide the steering column downward to install it onto the steering gear assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the intermediate shaft is aligned and fully seated.
  11. Install the cooling fan module assembly. See Cooling Fan Module (Remove and Replace).
  12. Install the RH outer tie rod end. See Tie Rod Outer - LH (Remove and Replace).
  13. Install the front wheels. See Wheel Assembly (Remove and Install).
  14. Install the front wheel caps. See Cap - Wheel (Model YL) (Remove and Replace).
  15. Remove the locking steering wheel tool and steering wheel level, then turn the steering wheel to the center position.
  16. Select Service Mode > Chassis > Alignment & Tires to confirm that the steering wheel is in center position.
    Informational PurposesAn informational icon, calling your attention
    Note
    Inspect whether the steering wheel illustration is approximately at 0 degrees. If the steering wheel is off by ±360 degrees, the steering column and steering gear assembly must be reinstalled accordingly.
  17. Install new bolt that attaches the steering column to the steering gear assembly.
    18 Nm (13.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 3/8" DR, SWIVEL, 13MM
    Informational PurposesAn informational icon, calling your attention
    Note
    If need, turn the steering wheel slightly to ensure that the bolt is in a convenient position for removal, then use a magnetic pickup tool to assist in installing the bolt.
  18. Raise the RH front window and close RH front door.
  19. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust as a separate activity. See Alignment Requirement - Suspension.