2026-01-29

1st Row Power Lumbar Seatback - LH (Model YL) (Remove and Install)

Correction code 13010200801 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. Disconnect the LV battery power. See LV Power (Disconnect and Connect) (Modify).
  2. Remove the driver seat back panel. See Shell - Seat Back - Driver Seat (Model YL) (Remove and Replace).
  3. Unhook the upper flaps that cover the LH and RH lower corners of the seat back frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Pull the flaps out of the metal retaining tabs to release them.
  4. Release the driver seat back trim retainers (x4) from the driver seat back frame.
  5. Pull the seat upholstery away from the inboard airbag to gain access to the electrical connector and then press both white tabs down to release and disconnect the driver seat inboard airbag electrical connector.
  6. Pull the seat upholstery away from the outboard airbag to gain access to the electrical connector and then press both white tabs down to release and disconnect the driver seat outboard airbag electrical connector.
  7. Disconnect the electrical connector from the driver seat back blower.
  8. Disconnect the electrical harness from the recliner motor connector.
  9. Disconnect the electrical harness from the lumbar valve pack and ECU.
  10. Disconnect the electrical harness from the lumbar pump connector.
  11. Partially release the clips (x6) and tab that attach the electrical harness to the seat frame.
  12. Release the clips (x2) that attach the lumbar pump to seat frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Squeeze the three lobes of the retaining clips and push towards the pump to release.
  13. Remove the bolt that attaches the power lumbar to the seat back frame.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  14. Remove the driver seat lumbar support from the driver seat back frame.
    1. Push the lower portion of power lumbar assembly towards the foam to release it from the seat back frame.
    2. Move the lumbar pump out from the frame.
    3. Slide the lumbar support assembly up to move the bottom of the assembly out from the seat back frame.
    4. Slide the lumbar support assembly down to move the upper of the assembly out from the seat back frame.

Install

  1. Slide the lumbar assembly posts into the top of the seat back frame and push the assembly in toward the foam. Then slide the assembly down towards the bottom of the seat frame and clip the bottom of the assembly to the seat frame.
  2. Install the bolt that attaches the power lumbar to the seat back frame.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  3. Install the clips (x2) that attach the lumbar pump to seat frame.
  4. Install the clips (x6) and tab that attach the electrical harness to the seat frame.
  5. Connect the electrical harness to the lumbar valve pack and ECU.
  6. Connect the electrical harness to the recliner motor connector.
  7. Connect the electrical harness to the lumbar pump connector.
  8. Connect the electrical connector to the driver seat back blower.
  9. Connect the electrical connector to the driver seat outboard air bag electrical connector.
  10. Connect the electrical connector to the driver seat inboard air bag electrical connector.
  11. Engage the driver seat back trim retainers (x4) to the driver seat back frame.
  12. Hook the upper flaps that cover the LH and RH lower corners of the seat back frame.
  13. Install the driver seat back panel. See Shell - Seat Back - Driver Seat (Model YL) (Remove and Replace).
  14. Connect the LV battery power. See LV Power (Disconnect and Connect) (Modify).