2026-03-11

Light - Dome - 3rd Row Seat - LH (Model YL) (Remove and Install)

Correction code 15200200301 FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Torque Specifications

Table 1. Torque Specifications: Light - Dome - 3rd Row Seat - LH (Model YL) (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolt that attaches the LH rear coat hook to the headliner
2.5 Nm (1.8 lbs-ft)
  • Torx T25 socket
 Reuse
Screw that attaches the LH 3rd row seat dome light to the headliner
0.65 Nm (6 lbs-in)
  • Torx T10 bit
  • Digital Torque Screwdriver 0.10Nm - 2.0Nm
 Reuse

Remove

  1. Open the LH rear door and lower the LH rear window.
  2. Remove the rear map light bezel. See Bezel - Map Light - Rear - LH (Model YL) (Remove and Replace).
  3. Move the LH 2nd row seat forward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust the seat back if needed.
  4. Open the liftgate.
  5. Fold the 3rd row seatback down.
    Informational PurposesAn informational icon, calling your attention
    Note
    Protect the seat back upholstery from any potential scratch or damage.
  6. Remove the LH C-pillar lower trim. See Trim - C-Pillar - Lower - LH (Model YL) (Remove and Replace).
  7. Release the clips (x14), locator pins (x2), and tabs (x2) that attach the LH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to aid the removal of the C-pillar upper trim.
  8. Release the clips (x10), locator pins (x4), and tabs (x2) that attach the LH C-pillar upper trim to the body, and then disconnect the seat dump switch connector and release the charging port release cable.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not pull the trim too far from the vehicle, as it is still attached by the connector and charging port release cable.
  9. Remove the rear headliner. See Rear Headliner (Model YL) (Remove and Replace).
  10. Push to open the LH rear coat hook.
  11. Release the tab to open the LH rear coat hook bolt cover.
  12. Remove the bolt that attaches the LH rear coat hook to the headliner.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  13. Release the clips (x4), tab, locator pin and tether to release the LH rear section of the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress the tabs (x2) of the tether to release it.
  14. Carefully insert an inflatable airbag between the headliner and the body, and inflate the airbag.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Take care not to damage the headliner.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to gain access to the working area.
  15. Disconnect the LH 3rd row seat dome light connector.
  16. Remove the screw that attaches the LH 3rd row seat dome light to the headliner, and then release the tabs (x2) to remove the light from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm

Install

  1. Align the tabs (x2) to install the light to the vehicle, and then install the screw that attaches the LH 3rd row seat dome light to the headliner.
    0.65 Nm (6 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 bit
    • Digital Torque Screwdriver 0.10Nm - 2.0Nm
  2. Connect the LH 3rd row seat dome light connector.
  3. Deflate the inflatable airbag, and then remove it from the vehicle.
  4. Install the clips (x4), tab, locator pin and tether to install the LH rear section of the headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure that the seal covers the interior trim panel.
  5. Install the bolt that attaches the LH rear coat hook to the headliner.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 socket
  6. Engage the tab to close the LH rear coat hook bolt cover.
  7. Push to close the LH rear coat hook.
  8. Install the rear headliner. See Rear Headliner (Model YL) (Remove and Replace).
  9. Connect the seat dump switch connector and install the charging port release cable, and then install the clips, locator pins, and tabs that attach the LH C-pillar upper trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    While installing the upper trim, make sure that the air vent is properly installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  10. Install the clips (x14), locator pins (x2), and tabs (x2) that attach the LH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  11. Move the 3rd row seatback back to its original position.
  12. Close the liftgate.
  13. Install the LH C-pillar lower trim. See Trim - C-Pillar - Lower - LH (Model YL) (Remove and Replace).
  14. Move the LH 2nd row seat back to its original position.
  15. Install the rear map light bezel. See Bezel - Map Light - Rear - LH (Model YL) (Remove and Replace).
  16. Raise the LH rear window and close the LH rear door.