2026-03-13

Radio Tuner FM/DAB (RHD) (Model Y L)(Remove and Replace)

Correction code NEW FRT 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

  • 2026-03-13: Released new procedure.

Remove

  1. Remove the rear headliner panel. See Rear Headliner (Model YL) (Remove and Replace).
  2. Remove the RH C-pillar lower trim. See Trim - C-Pillar - Lower - LH (Model YL) (Remove and Replace).
  3. Release the clips (x14), locator pins (x2), and tabs (x2) that attach the RH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to aid the removal of the C-pillar upper trim.
  4. Release the clips (x10), locator pins (x4), and tabs (x3) that attach the RH C-pillar upper trim to the body.
  5. Push open the RH coat hook.
  6. Open the RH coat hook screw cover.
  7. Remove the RH coat hook screw.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 1/4" DR, HEX BIT, T25 TORX
  8. Release the clips (x4), tabs (x3), location pin, and tether that attach the RH rear section headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Depress the tabs (x2) to release the tether from the body side.
  9. Disconnect the electrical connectors (x3) from the radio tuner.
  10. Remove the bolts (x2) that attach the radio tuner to the vehicle, then release the clip and location pins (x2).
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 1/4in Dr. 12pt. Deep x 10mm

Replace

  1. Secure the location pins (x2) and clip, then install the bolts (x2) that attach the radio tuner to the vehicle.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Socket 1/4in Dr. 12pt. Deep x 10mm
  2. Connect the electrical connectors (x3) to the radio tuner.
  3. Align the location pin, secure the clips (x4), tabs (x3), and tether that attach the RH rear section headliner to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    Ensure the tether is secured to the body and the seal covers the interior trim panel.
  4. Install the RH coat hook screw.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • SKT, 1/4" DR, HEX BIT, T25 TORX
  5. Close the RH coat hook screw cover.
  6. Push close the RH coat hook.
  7. Secure the clips (x10), locator pins (x4), and tabs (x3) that attach the RH C-pillar upper trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    While installing the upper trim, make sure that the air vent is properly installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  8. Install the clips (x14), locator pins (x2), and tabs (x2) that attach the RH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  9. Install the RH C-pillar lower trim. See Trim - C-Pillar - Lower - LH (Model YL) (Remove and Replace).
  10. Install the rear headliner panel. See Rear Headliner (Model YL) (Remove and Replace).