2025-09-11

Insulator - Rear Quarter Panel - LH (Model YL) (Remove and Replace)

Correction code 15301001302 FRT 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Remove

  1. Open the LH rear door and lower the LH rear window.
  2. Move the LH 2nd row seat forward.
    Informational PurposesAn informational icon, calling your attention
    Note
    Adjust the seat back if needed.
  3. Open the liftgate.
  4. Fold the 3rd row seatback down.
    Informational PurposesAn informational icon, calling your attention
    Note
    Protect the seat back upholstery from any potential scratch or damage.
  5. Remove the LH C-pillar lower trim. See Trim - C-Pillar - Lower - LH (Model YL) (Remove and Replace).
  6. Release the clips (x14), locator pins (x2), and tabs (x2) that attach the LH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    This is to aid the removal of the C-pillar upper trim.
  7. Release the clips (x10), locator pins (x4), and tabs (x2) that attach the LH C-pillar upper trim to the body, and then disconnect the seat dump switch connector and release the charging port release cable.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not pull the trim too far from the vehicle, as it is still attached by the connector and charging port release cable.
  8. Remove the bolt that attaches the LH body harness ground strap to the LH rear quarter panel.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  9. Release the clips (x3) that attach the LH body harness to the LH rear quarter panel.
  10. Release the clips (x6) that attach the LH rear quarter panel insulator to the body, and then remove the insulator from the vehicle.

Install

  1. Install the clips (x6) that attach the LH rear quarter panel insulator to the body.
  2. Install the clips (x3) that attach the LH body harness to the LH rear quarter panel.
  3. Install the bolt that attaches the LH body harness ground strap to the LH rear quarter panel.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm deep socket
  4. Connect the seat dump switch connector and install the charging port release cable, and then install the clips, locator pins, and tabs that attach the LH C-pillar upper trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    While installing the upper trim, make sure that the air vent is properly installed.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  5. Install the clips (x14), locator pins (x2), and tabs (x2) that attach the LH trunk side trim to the body.
    Informational PurposesAn informational icon, calling your attention
    Note
    After installation, make sure that the seal fully covers the edge of the trim.
  6. Move the 3rd row seatback back to its original position.
  7. Close the liftgate.
  8. Install the LH C-pillar lower trim. See Trim - C-Pillar - Lower - LH (Model YL) (Remove and Replace).
  9. Move the LH 2nd row seat back to its original position.
  10. Raise the LH rear window and close the LH rear door.