2025-09-12

Frame - Seat Back - 2nd Row - LH (Model YL) (Remove and Replace)

Correction code 13020200102 FRT 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and FRT listed above reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Torque Specifications

Table 1. Torque Specifications: Frame - Seat Back - 2nd Row - LH (Model YL) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
Bolts (x3) that attach the headrest frame assembly to the LH 2nd row seat back rest assembly
10 Nm (7.4 lbs-ft)
  • 10 mm socket
 Reuse
Bolt that attaches the LH 2nd row seat belt buckle to the cushion frame assembly
45 Nm (33.2 lbs-ft)
  • Torx T50 socket
 Replace 3880753-C1-D
Outboard bolts (x2) that attach the seat back frame to the LH 2nd row seat cushion frame assembly
43 Nm (31.7 lbs-ft)
  • Torx T50 socket
 Replace 1128435-00-C
Inboard bolts (x2) that attach the seat back frame to the LH 2nd row seat cushion frame assembly
43 Nm (31.7 lbs-ft)
  • Torx T50 socket
 Replace 1128435-00-C

Remove

  1. Remove the LH 2nd row seat assembly from the vehicle. See Seat Assembly - 2nd Row - LH (Model YL) (Remove and Install).
  2. Remove the toe kick cover from the LH 2nd row seat. See Toe Kick Cover - 2nd Row Seat - LH (Model YL) (Remove and Replace).
  3. Remove the LH 2nd row seat back panel from the LH 2nd row seat. See Panel - Seat Back - 2nd Row Seat - LH (Model YL) (Remove and Replace).
  4. Disconnect the LH 2nd row seat back tilt sensor connector.
  5. Disconnect the LH 2nd row seat back heat pad connector.
  6. Disconnect the LH 2nd row seat recline motor connector.
  7. Disconnect the LH 2nd row seat back blower connector.
  8. Remove the seat harness from the LH 2nd row seat back rest assembly by detaching the secure clips (x2) and hooks (x4).
  9. Remove the bolts (x3) that attach the headrest frame assembly to the LH 2nd row seat back rest assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  10. Remove the clips (x2) that attach the seat back rest frame to the LH 2nd row seat.
  11. Release the hooks (x4) that attach the seat back foam assembly to the LH 2nd row seat back rest frame, and then remove the seat back foam assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care to avoid damaging the seat trim.
  12. Remove and discard both the LH 2nd row seat belt buckle and the bolt that attaches the buckle to the cushion frame assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  13. Release the clip and disconnect the LH 2nd row seat buckle connector.
  14. Remove the push clip securing the inboard side shield carrier to the LH 2nd row seat cushion frame assembly.
  15. Release the clip that attaches the inboard side shield carrier to the LH 2nd row seat cushion frame assembly, then remove the inboard side shield carrier.
    Informational PurposesAn informational icon, calling your attention
    Note
    Avoid excessive force to prevent damage to decorative pieces.
  16. Remove the push clip that attaches the outboard side shield carrier to the LH 2nd row seat cushion frame assembly.
  17. Remove the harness clamp from the LH 2nd row seat cushion frame assembly.
  18. Lift the outboard side shield carrier slightly outward, then remove and discard the outboard bolts (x2) that attach the seat back frame to the LH 2nd row seat cushion frame assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  19. Remove and discard the inboard bolts (x2) that attach the seat back frame to the LH 2nd row seat cushion frame assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  20. Rotate the seat back frame away from the seat cushion frame, then lift the seat back frame straight up to remove the frame from the LH 2nd row seat cushion frame assembly.

Install

  1. Install the seat back frame to the LH 2nd row seat cushion frame assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    The seat back frame can rest on the seat cushion frame without fasteners.
  2. Lift the outboard side shield carrier slightly outward, then install new outboard bolts (x2) that attach the seat back frame to the LH 2nd row seat cushion frame assembly.
    43 Nm (31.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  3. Install new inboard bolts (x2) that attach the seat back frame to the LH 2nd row seat cushion frame assembly.
    43 Nm (31.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  4. Install the harness clamp to the LH 2nd row seat cushion frame assembly.
  5. Install the push clip that attaches the outboard side shield carrier to the LH 2nd row seat cushion frame assembly.
  6. Secure the clip and install the inboard side shield carrier to the LH 2nd row seat cushion frame assembly.
    Informational PurposesAn informational icon, calling your attention
    Note
    Avoid excessive force to prevent damage to decorative pieces.
  7. Install the push clip securing the inboard side shield carrier to the LH 2nd row seat cushion frame assembly.
  8. Install new LH 2nd row seat belt buckle (3880753-C1-D) to the cushion frame assembly with the included new bolt.
    45 Nm (33.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 socket
  9. Connect the LH 2nd row seat buckle connector and secure the clip.
  10. Secure the hooks (x4) that attach the seat back foam assembly to the LH 2nd row seat back rest frame.
    Informational PurposesAn informational icon, calling your attention
    Note
    Take care to avoid damaging the seat trim.
  11. Install the clips (x2) that attach the seat back rest frame to the LH 2nd row seat.
  12. Install the bolts (x3) that attach the headrest frame assembly to the LH 2nd row seat back rest assembly.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10 mm socket
  13. Secure the clips (x2) and hooks (x4) to install the seat harness to the LH 2nd row seat back rest assembly.
  14. Connect the LH 2nd row seat recline motor connector.
  15. Connect the LH 2nd row seat back heat pad connector.
  16. Connect the LH 2nd row seat back tilt sensor connector.
  17. Connect the LH 2nd row seat back blower connector.
  18. Remove the LH 2nd row seat back panel from the LH 2nd row seat. See Panel - Seat Back - 2nd Row Seat - LH (Model YL) (Remove and Replace).
  19. Remove the toe kick cover from the LH 2nd row seat. See Toe Kick Cover - 2nd Row Seat - LH (Model YL) (Remove and Replace).
  20. Remove the LH 2nd row seat assembly from the vehicle. See Seat Assembly - 2nd Row - LH (Model YL) (Remove and Install).