2026-07-02

Basic Vehicle Inspection (Inspection)

교정 코드 00030700 FRT 1.02 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  • 2026-06-18: Released new procedure.

Procedure

  1. Function check LH front door (exterior)
    Informational PurposesAn informational icon, calling your attention
    참고
    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
  2. Function check all windows from the master switch
    Informational PurposesAn informational icon, calling your attention
    참고
    Check operation with door closed, Document any abnormal operation/noises
  3. Function check LH rear door (exterior)
    Informational PurposesAn informational icon, calling your attention
    참고
    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
  4. Function check RH rear door (exterior)
    Informational PurposesAn informational icon, calling your attention
    참고
    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
  5. Function check RH front door (exterior)
    Informational PurposesAn informational icon, calling your attention
    참고
    Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
  6. Verify operation of all exterior lights
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance, Headlamps, fog lights, license plate, tail, brake, reverse,  & side repeater
  7. Engage drive rails and activate windshield washer and wiper operation
    Informational PurposesAn informational icon, calling your attention
    참고
    Engage drive rails and hold down on the washer button, Verify wipers and washer is operating as intended
  8. Function check horn
  9. Open hood
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Frunk Open
  10. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    8x clips
  11. Remove LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    10x clips, (*Use this step for Palladium S procedures)
  12. Remove RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    10x clips
  13. Remove front underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips
  14. Remove frunk access panel
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, 3x hooks, 1x connector
  15. Remove frunk carpet
  16. Remove frunk assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, 10mm, 5 Nm
  17. Perform inspection of under hood area
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
  18. Inspect brake fluid level
  19. Inspect coolant level and top off as necessary
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure that the fluid level is at the Max line, Top off fluid as required
  20. Fill washer reservoir with fluid
  21. Raise vehicle fully and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    참고
    Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
  22. Remove front aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    5x push clips
  23. Release front aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    9x bolts, 10mm, 6 Nm
  24. Release rear aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    4x push clips
  25. Remove rear aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    16x bolts, 10mm, 6 Nm
  26. Perform inspection of vehicle underside components front and rear
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
  27. Inspect underside of vehicle for fluid leaks
  28. Perform inspection of steering components
    Informational PurposesAn informational icon, calling your attention
    참고
    Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
  29. Perform inspection of front suspension components
    Informational PurposesAn informational icon, calling your attention
    참고
    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
  30. Perform inspection of rear suspension components
    Informational PurposesAn informational icon, calling your attention
    참고
    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
  31. Inspect underside of battery for damage
  32. Check tire pressures
    Informational PurposesAn informational icon, calling your attention
    참고
    4x tires, Adjust to specification if necessary
  33. Inspect condition of LH front tire
    Informational PurposesAn informational icon, calling your attention
    참고
    Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
  34. Measure and record LH front tread depth
    Informational PurposesAn informational icon, calling your attention
    참고
    Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
  35. Perform visual inspection of LH front brake pads
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
  36. Inspect LH front brake rotor condition
    Informational PurposesAn informational icon, calling your attention
    참고
    Check for excessive rust or wear, Minimum spec 30mm
  37. Inspect condition of LH rear tire
    Informational PurposesAn informational icon, calling your attention
    참고
    Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
  38. Measure and record LH rear tread depth
    Informational PurposesAn informational icon, calling your attention
    참고
    Record at least 3 measurements: Inner, Middle, Add line to replace if under 5/32 inch tread remaining
  39. Perform visual inspection of LH rear brake pads
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
  40. Inspect LH rear brake rotor condition
    Informational PurposesAn informational icon, calling your attention
    참고
    Check for excessive rust or wear, Minimum spec 26mm
  41. Inspect condition of RH rear tire
    Informational PurposesAn informational icon, calling your attention
    참고
    Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
  42. Measure and record RH rear tread depth
    Informational PurposesAn informational icon, calling your attention
    참고
    Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
  43. Perform visual inspection of RH rear brake pads
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
  44. Inspect RH rear brake rotor condition
    Informational PurposesAn informational icon, calling your attention
    참고
    Check for excessive rust or wear, Minimum spec 26mm
  45. Inspect condition of RH front tire
    Informational PurposesAn informational icon, calling your attention
    참고
    Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
  46. Measure and record RH front tread depth
    Informational PurposesAn informational icon, calling your attention
    참고
    Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
  47. Perform visual inspection of RH front brake pads
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
  48. Inspect RH front brake rotor condition
    Informational PurposesAn informational icon, calling your attention
    참고
    Check for excessive rust or wear, Minimum spec 30mm
  49. Inspect brake hose condition
    Informational PurposesAn informational icon, calling your attention
    참고
    Look for evidence of brake hose(s) rubbing on surrounding components, Inspect hose connections for evidence of leaks, Verify hoses are routed properly and secured to retaining brackets
  50. Install rear aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    16x bolts, 10mm, 6 Nm, Apply Loctite 222 onto mid aero shield bolts and install fasteners securing mid aero shield to vehicle
  51. Position rear aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    4x push clips
  52. Secure front aero shield to vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    9x bolts, 10mm, 6 Nm, Apply Loctite 222 onto front aero shield bolts
  53. Install front aero shield
    Informational PurposesAn informational icon, calling your attention
    참고
    5x push clips
  54. Lower vehicle fully
    Informational PurposesAn informational icon, calling your attention
    참고
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  55. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    참고
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  56. Install frunk assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, 10mm, 5 Nm
  57. Install frunk carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    Verify carpet is properly seated under the seal
  58. Install frunk access panel
    Informational PurposesAn informational icon, calling your attention
    참고
    3x clips, 3x hooks, 1x connector
  59. Install front underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips
  60. Install RH underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    10x clips
  61. Install LH underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    10x clips
  62. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    참고
    8x clips
  63. Close hood
    Informational PurposesAn informational icon, calling your attention
    참고
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  64. Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance
    Informational PurposesAn informational icon, calling your attention
    참고
    The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
  65. Inspect vehicles alignment
    Informational PurposesAn informational icon, calling your attention
    참고
    Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction