교정 코드 17102802 0.48 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.

1. Open LH front door
2. Open LH rear door
3. Move LH front seat forward

   

4. Partially release LH lower B-pillar
   참고

   6x clips, Release from upper trim and body

   

   

5. Remove LH upper B-pillar
   참고

   7x clips, Release clips and route seatbelt through B-pillar, Be cautious not to separate the upper B-pillar, There are plastic welds near the center of trim holding upper and lower portion together

   

   

6. Disconnect LH rear door harness connector from body harness
   참고

   1x connector, route harness from B-pillar to gain access

   

   

7. Remove service covers from LH rear door panel
   참고

   2x covers

   

   

8. Remove fasteners securing LH rear door panel under armrest and door trim handle
   참고

   2x bolts, T30, 6 Nm

   

9. Remove LH rear door panel assembly
   참고

   7x clips, 1x connector, Pull bottom of door panel to release clips then lift panel up to disengage from inner belt seal, Pull red tab to disengage lock then disconnect door harness

   

   

   

10. Disconnect LH rear door handle controller connector
    참고

    1x connector, Pull white tab to disengage lock then disconnect

    

    

11. Disconnect LH rear door pressure sensor connector
    참고

    1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

    

12. Remove bolts securing LH rear closeout panel assembly to door
    참고

    6x bolts, 8mm, 4 Nm

    

13. Release clips securing harness and remove LH rear closeout panel assembly
    참고

    3x clips, Release clips from back of panel to prevent damage

    

    

14. Disconnect LH rear door speaker connector
    참고

    1x connector

    

15. Remove bolts securing speaker to LH rear door
    참고

    4x bolts, 8mm, 4 Nm

    

    

16. Remove speaker from LH rear door
    참고

    2x datums, Lift speaker up then pull away from door

    

    

    

17. Disconnect LH rear regulator motor connector
    참고

    1x connector

    

    

18. Disconnect connector for LH rear door handle
    참고

    1x connector, Release red locking tab before disconnecting

    

19. Remove rubber grommets and push into LH rear door
    참고

    Push both rubber grommets into LH rear door with harness pass through and connector.

    

    

20. Release clips holding harness to LH rear door
    참고

    8X clips

    

    

    

21. Remove harness from LH rear door

    

    

22. Install LH rear door harness into LH rear door
    참고

    Slide connector for regulator motor between regulator and door

    

    

23. Attach clips to fasten harness to LH rear door
    참고

    8x clips

    

    

    

24. Install rubber grommets to LH rear door and B-pillar
    참고

    Slide connector and harness into B-pillar, press firmware to ensure proper sealing

    

    

25. Connect door handle harness
    참고

    1x connector, Press in red locking tab

    

26. Connect LH rear regulator motor connector
    참고

    1x connector

    

    

27. Install speaker onto LH rear door
    참고

    2x datums

    

    

    

28. Install bolts securing speaker to LH rear door
    참고

    4x bolts, 8mm, 4 Nm, Hand start bolts to prevent stripping threads

    

    

29. Connect LH rear door speaker connector
    참고

    1x connector

    

30. Install LH rear closeout panel assembly onto door
    참고

    6x bolts, 8mm, 4 Nm, Hand start bolts to prevent stripping threads

    

    

31. Secure harness onto LH rear closeout panel assembly
    참고

    3x clips, An audible click ensures clips are fully engaged

    

32. Connect LH rear door pressure sensor connector
    참고

    1x connector, Engage locking tab

    

33. Connect LH rear door handle controller connector
    참고

    1x connector, Engage locking tab

    

    

34. Install LH upper B-pillar
    참고

    7x clips, Route seatbelt through B-pillar, Replace any damaged or missing clips

    

    

35. Reinstall top portion of LH lower B-pillar
    참고

    6x clips, Replace any damaged or missing clips

    

    

36. Move LH front seat to original position

    

37. Install LH rear door panel assembly
    참고

    7x clips, 1x connector, Connect door harness then engage locking tab, Slide top portion of panel into door seal first, then swing bottom into place, Ensure all clips and retainers are seated

    

    

    

38. Install fasteners securing door panel to rear door
    참고

    2x bolts, T30, 6 Nm

    

39. Install service covers onto LH rear door
    참고

    2x covers

    

    

40. Close LH rear door
41. Close LH front door