2026-07-31

Coax Cable - Side Repeater - Front - LH and RH (Overlay) (Remove and Replace)

교정 코드 17403032 FRT 2.16 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  • 2026-07-09: Released new procedure.

Overlay

  1. Open both front doors and lower both front windows.
  2. Remove the wiper module. See 와이퍼 모듈(탈거 및 교체).
  3. Remove LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 2x tabs
  4. Remove LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips
  5. Remove LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, 2x magnets
  6. Move LH front seat backward
  7. Remove LH front floor mat
  8. Remove LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips
  9. Fold LH front cabin carpet aside for full access
  10. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 2x tabs
  11. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, Partially release seal if needed
  12. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    참고
    3x magnets, 1x connector, 4x datums
  13. Move RH front seat backward
  14. Remove RH front floor mat
  15. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips
  16. Fold RH front cabin carpet aside for access
    Informational PurposesAn informational icon, calling your attention
    참고
    Caution not to damage styrofoam of carpet
  17. Release harness from RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip
  18. Remove RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  19. Disconnect brown fakra connection from car computer
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, X836
  20. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  21. Remove LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    참고
    Lift every other spoke at a time until cap is released from rim
  22. Loosen LH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  23. Remove RH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    참고
    Lift every other spoke at a time until cap is released from rim
  24. Loosen RH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  25. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    참고
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  26. Remove LH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  27. Partially release rear portion of LH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    참고
    5x clips, 1x fan clip, Move liner aside
  28. Disconnect LH front repeater
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors
  29. Remove RH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  30. Partially release rear portion of RH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    참고
    5x clips, 1x fan clip, Move liner aside
  31. Disconnect RH front repeater
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors
  32. Release LH grommet from body
    Informational PurposesAn informational icon, calling your attention
    참고
    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
  33. Remove electrical tape securing harness bundle to rubber dust boot
  34. Remove the connector from the coax cable
    Informational PurposesAn informational icon, calling your attention
    참고
    Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
  35. Apply harness tape onto LH coax overlay cable before installation
    Informational PurposesAn informational icon, calling your attention
    참고
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  36. Position LH coax overlay cable into place, Place through LH wheel liner and dust boot towards interior cabin
    Informational PurposesAn informational icon, calling your attention
    참고
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  37. Pull LH coax overlay cable through bulkhead and into interior cabin
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull harness toward car computer under dashboard
  38. Position LH coax overlay cable onto main dash body harness, Secure cable onto harness using zip ties
    Informational PurposesAn informational icon, calling your attention
    참고
    5x zip-ties, Trim off excess material after harness has been secured
  39. Secure coax overlay through LH wheel liner and frunk harness
    Informational PurposesAn informational icon, calling your attention
    참고
    4x zip-ties, Trim off excess material after harness has been secured
  40. Depin the RH side coax cable (Terminal 1) from the connector X846
    Informational PurposesAn informational icon, calling your attention
    참고
    Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  41. Insert coax overlay terminal into connector X846
  42. Remove the coax cable from the Connector X846
    Informational PurposesAn informational icon, calling your attention
    참고
    Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
  43. Insert the connector locking tab and reconnect X846 together
  44. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    참고
    Cut the coax connector only
  45. Connect LH front repeater
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  46. Secure LH grommet onto body
    Informational PurposesAn informational icon, calling your attention
    참고
    Use electrical tape to wrap the end of the dust boot
  47. Secure rear portion of LH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    참고
    5x clips, 1x fan clip, Secure liner
  48. Install LH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  49. Release RH grommet from body
    Informational PurposesAn informational icon, calling your attention
    참고
    With a razor blade, carefully cut the electrical tape away exposing the rubber dust boot
  50. Remove electrical tape securing harness bundle to rubber dust boot
  51. Remove the connector from the coax cable
    Informational PurposesAn informational icon, calling your attention
    참고
    Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
  52. Apply harness tape onto RH coax overlay cable before installation
    Informational PurposesAn informational icon, calling your attention
    참고
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  53. Position RH coax overlay cable into place, Place through RH wheel liner and dust boot towards interior cabin
    Informational PurposesAn informational icon, calling your attention
    참고
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  54. Pull RH coax overlay cable through bulkhead and into interior cabin
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull harness toward car over car computer
  55. Position RH coax overlay cable onto harness, Secure cable onto car computer harness
    Informational PurposesAn informational icon, calling your attention
    참고
    3x zip-ties, Trim off excess material after harness has been secured
  56. Secure coax overlay through RH wheel liner and frunk harness
    Informational PurposesAn informational icon, calling your attention
    참고
    4x zip-ties, Trim off excess material after harness has been secured
  57. Depin the RH side coax cable (Terminal 1) from the connector X846
    Informational PurposesAn informational icon, calling your attention
    참고
    Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  58. Remove the coax cable from the Connector X846
    Informational PurposesAn informational icon, calling your attention
    참고
    Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
  59. Insert coax overlay terminal into connector X846
  60. Insert the connector locking tab and reconnect X846 together
  61. Connect brown fakra connection onto car computer
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, X836
  62. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    참고
    Cut the coax connector only
  63. Connect RH front repeater
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  64. Secure RH grommet onto body
    Informational PurposesAn informational icon, calling your attention
    참고
    Use electrical tape to wrap the end of the dust boot
  65. Secure rear portion of RH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    참고
    5x clips, 1x fan clip, Secure liner
  66. Install RH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  67. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    참고
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  68. Torque LH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  69. Install LH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    참고
    Align valve stem with cap
  70. Torque RH front wheel
    Informational PurposesAn informational icon, calling your attention
    참고
    5x nuts, 21mm, 175 Nm
  71. Install RH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    참고
    Align valve stem with cap
  72. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    참고
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  73. Fold LH main carpet back into place
  74. Install LH console side carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips
  75. Install LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, 2x magnets
  76. Install LH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, Verify weather seal is seated properly
  77. Install LH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 2x tabs, Verify weather seal is seated properly
  78. Install LH front floor mat
  79. Move LH front seat to original position
  80. Install RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  81. Secure harness to RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip
  82. Fold RH main carpet back into place
    Informational PurposesAn informational icon, calling your attention
    참고
    Caution not to damage styrofoam of carpet
  83. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips
  84. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    참고
    3x magnets, 4x datums, 1x connector
  85. Install RH front floor mat
  86. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    7x clips, Verify weather seal is seated properly
  87. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x clip, 2x tabs, Verify weather seal is seated properly
  88. Move RH front seat to original position
  89. Install the wiper module. See 와이퍼 모듈(탈거 및 교체).
  90. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
  91. Reset DAS on UI
    Informational PurposesAn informational icon, calling your attention
    참고
    Select "Driver Assist" > "Cameras" > "Reset DAS", Ensure all cameras and reset DAS icon turn green on UI, If not you need to investigate further why a the particular DAS component is flagging red
  92. ODIN 루틴 실행 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  93. Raise both front windows
  94. Close RH front door
  95. Close LH front door
    Informational PurposesAn informational icon, calling your attention
    참고