17/06/2024 21:25:22

버스바 - 충전 포트(CP)-HV 배터리(유럽/중동/아프리카)(탈거 및 교체)

교정 코드 44013142 0.78 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.

  • 2023-08-25: Added link to charge port voltage check procedure.
  • 2023-07-03: Cleaned up procedure.
Informational PurposesAn informational icon, calling your attention
참고
이 절차는 이 부품의 전역 새로 고침 버전을 위한 것입니다. 이 부품의 원래 버전에 대한 절차는 여기에 있습니다. 버스바 - 충전 포트(CP)에서 HV 배터리 (탈거 및 교체).

탈거

  1. Open all four doors.
  2. Lower the LH and RH front windows.
  3. Move the driver and front passenger seats fully forward.
  4. Open the liftgate.
  5. Remove the rear trunk parcel shelf. See 트렁크 선반 - 후면 트렁크(탈거 및 교체).
  6. Remove the rear trunk load floor. See 트렁크 적재함 바닥 - 후면(탈거 및 교체).
  7. Remove the side trunk load floor. See 트렁크 적재함 바닥 - 측면(탈거 및 교체).
  8. Remove the trunk sill trim. See 트림 - 실 - 트렁크(탈거 및 교체).
  9. Remove the LH and RH 2nd row seat outer bolsters. See 볼스터 - 외측 - 시트 - 2열 - LH(탈거 및 교체).
  10. Remove the 2nd row lower seat cushion. See 시트 쿠션 - 하단 - 2열(탈거 및 교체).
  11. Fold the LH 2nd row 60 seat down.
    Informational PurposesAn informational icon, calling your attention
    참고
    Seat can be folded from the backrest button or trunk switch.
    Informational PurposesAn informational icon, calling your attention
    참고
    Since the seat cushion is not present, protect the seat as required.
  12. Open the charge port door using the vehicle touchscreen.
  13. Open the hood.
  14. Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  15. Disconnect LV power. See LV 전원(연결 해제 및 연결).
  16. Perform the charge port voltage check procedure. See 충전 포트 전압 점검.
  17. Remove the rear wall rear trunk trim. See 트림 - 후면 트렁크 - 후방 벽(탈거 및 교체).
  18. Remove the LH trunk load floor bracket. See 브래킷 - 트렁크 적재함 바닥 - LH(탈거 및 교체).
  19. Remove the trunk floor front trim. See 트림 - 전면 - 플로어 - 트렁크(탈거 및 교체).
  20. Remove the LH lower C-pillar trim. See 트림 - C필러 - 하단 - LH(탈거 및 교체).
  21. Remove the LH mid C-pillar trim. See 트림 - C필러 - 중간 - LH(탈거 및 교체).
  22. Release the LH upper C-pillar trim, and then set it aside. See 트림 - C필러 - 상단 - LH(탈거 및 교체).
    Informational PurposesAn informational icon, calling your attention
    참고
    Do not remove the lower bolt that attaches the LH 2nd row seat belt retractor.
  23. Remove the LH trunk side trim. See 트림 - 사이드 - 트렁크 - LH (탈거 및 교체).
  24. Disconnect the 60 seat electrical connector.
  25. Release the harness clip for the 60 seat and the rear seat cushion.
  26. Remove the LH 2nd row cushion support block. See 지지대 블록 - 2열 쿠션 - LH(탈거 및 교체).
  27. Remove the bolt that attaches the busbar cover access door.
    9 Nm (6.6 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
  28. Remove the bolts (x2) that attach the busbars to the HV header, and then release the busbars.
    9 Nm (6.6 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
  29. Disconnect the AC inlet harness from the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    Release the locking tab.
  30. Disconnect the charge port electrical connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    Carefully remove the white locking tab. Press the tab to release the electrical connector from the charge port. Continue to pull off the connector. The connector is intended to disengage the safety cap when released.
  31. Disconnect the AC inlet electrical harness from the charge port.
    Informational PurposesAn informational icon, calling your attention
    참고
    Release the dual step locking tab.
  32. Release the tabs (x3) that attach the charge port safety cap to the charge port, and then remove it from the vehicle.
  33. Remove the nuts (x2) that attach the charge port busbars to the charge port, and then remove the busbar leads from the studs.
    9 Nm (6.6 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 11mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    Nuts have captured washers.
    Informational PurposesAn informational icon, calling your attention
    참고
    Take caution of any tension present with the busbars.
  34. Remove the busbars from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    참고
    Maneuver the busbars rearward, and then remove them through the liftgate. Rotate them to clear the seat bracket.

장착

  1. Clean the HV connector contact surface of residual Penetrox with an Isopropyl Alcohol (IPA) wipe.
    Informational PurposesAn informational icon, calling your attention
    참고
    Allow 1 minute dry time after removing Penetrox.
    Informational PurposesAn informational icon, calling your attention
    참고
    New busbars come with Penetrox applied to the HV connector.
  2. Clean the charge port assembly busbar contact surface of residual Penetrox with an IPA wipe.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use a plastic trim tool to push the IPA wipe down between plastic divider.
    Informational PurposesAn informational icon, calling your attention
    참고
    Allow 1 minute dry time after removing the Penetrox.
  3. Verify that the charge port studs (x2) are tightened to specification.
    2 Nm (1.5 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • Torx T10 비트
  4. Install the busbars into the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance.
    Informational PurposesAn informational icon, calling your attention
    참고
    Maneuver the busbars forward through the liftgate, and then rotate to clear the seat bracket.
  5. Connect the AC inlet harness to HV battery electrical connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    Secure the locking tab.
  6. Secure the busbars onto the HV header, and then install bolts (x2).
    9 Nm (6.6 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
  7. Apply Penetrox to the backside of the busbar leads.
    Informational PurposesAn informational icon, calling your attention
    참고
    Apply 2 drops of Penetrox A-13 about 5 mm in diameter to either side of the hole on both leads. Spread evenly to verify the contact surface is fully covered.
  8. Install the nuts (x2) that attach the charge port busbar leads to the charge port assembly.
    11 Nm (8.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구 사용을 권장합니다.
    • 9mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    Nuts have captured washers.
    Informational PurposesAn informational icon, calling your attention
    참고
    If excessive force is required to seat the busbars, they may have been bent. Inspect for damage and replace it, if necessary.
  9. Connect the AC inlet harness onto the charge port.
    Informational PurposesAn informational icon, calling your attention
    참고
    Secure the dual step locking tab.
  10. Connect the charge port electrical connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    Fully engage the electrical connector and white locking tab. The connector is intended to lock the safety cap in place.
  11. Inspect HV insulating gloves.
    Informational PurposesAn informational icon, calling your attention
    참고
    Check gloves for damage prior to use. Refer to service document TN-15-92-003 for information on inspecting HV gloves: https://service.tesla.com/user/documents?searchText=TN-15-92-003
  12. Put on the HV insulating gloves and leather over gloves.
  13. Perform a Hioki resistance test at each HV joint from the HV busbar lead to the charge port stud (x2 HV joints).
    Informational PurposesAn informational icon, calling your attention
    참고
    When using the Hioki tester, verify that the meter has been properly adjusted and set prior to usage.
    Informational PurposesAn informational icon, calling your attention
    참고
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.270 mΩ (270 μΩ).
    • If the resistance is greater than 0.270 mΩ (270 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
    • If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.
    • If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki resistance test passed. Proceed to next step.
  14. Perform a Hioki resistance test at each HV joint from the HV busbar lead to the bolt head (x2 HV joints).
    Informational PurposesAn informational icon, calling your attention
    참고
    When using the Hioki tester, verify that the meter has been properly adjusted and set prior to usage.
    Informational PurposesAn informational icon, calling your attention
    참고
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.270 mΩ (270 μΩ).
    • If the resistance is greater than 0.270 mΩ (270 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
    • If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.
    • If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki resistance test passed. Proceed to next step.
  15. Remove the leather glove protectors and HV insulating gloves.
  16. Install the bolt that attaches the busbar cover access door.
    9 Nm (6.6 lbs-ft)
    팁: 다음 공구 사용을 권장합니다.
    • 9mm 소켓
  17. Install the LH 2nd row cushion support block. See 지지대 블록 - 2열 쿠션 - LH(탈거 및 교체).
  18. Secure the tabs (x3) that attach the charge port safety cap to the charge port assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    The safety cap will click into position.
  19. Secure the harness clip for the 60 seat and rear seat cushion.
  20. Connect the 60 seat electrical connector.
  21. Install the LH trunk side trim. See 트림 - 사이드 - 트렁크 - LH (탈거 및 교체).
  22. Install the LH upper C-pillar trim. See 트림 - C필러 - 상단 - LH(탈거 및 교체).
  23. Install the LH mid C-pillar trim. See 트림 - C필러 - 중간 - LH(탈거 및 교체).
  24. Install the LH lower C-pillar trim. See 트림 - C필러 - 하단 - LH(탈거 및 교체).
  25. Install the trunk floor front trim. See 트림 - 전면 - 플로어 - 트렁크(탈거 및 교체).
  26. Install the LH trunk load floor bracket. See 브래킷 - 트렁크 적재함 바닥 - LH(탈거 및 교체).
  27. Install the rear wall rear trunk trim. See 트림 - 후면 트렁크 - 후방 벽(탈거 및 교체).
  28. Install the trunk sill trim. See 트림 - 실 - 트렁크(탈거 및 교체).
  29. Install the side trunk load floor. See 트렁크 적재함 바닥 - 측면(탈거 및 교체).
  30. Install the rear trunk load floor. See 트렁크 적재함 바닥 - 후면(탈거 및 교체).
  31. Install the rear trunk parcel shelf. See 트렁크 선반 - 후면 트렁크(탈거 및 교체).
  32. Close the liftgate.
  33. Restore the LH 2nd row 60 seat into upright position.
    Informational PurposesAn informational icon, calling your attention
    참고
    Remove seat cushion protection.
  34. Install the 2nd row lower seat cushion. See 시트 쿠션 - 하단 - 2열(탈거 및 교체).
  35. Install the LH and RH 2nd row seat outer bolsters. See 볼스터 - 외측 - 시트 - 2열 - LH(탈거 및 교체).
  36. Reconnect LV power. See LV 전원(연결 해제 및 연결).
  37. Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  38. Close the hood.
  39. Verify operation of the vehicle charging system.
  40. Close the charge port door.
  41. Raise the LH and RH front windows.
  42. Restore the driver and front passenger seats.
  43. Close all four doors.