2026-03-13

카메라 - 후방(HW4)(탈거 및 교체)

교정 코드 17222012 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-03-02: Updated calibration steps to use ServiceUI.
  • 2023-06-20: Switch the steps so that DAS Reset occurs directly before the Camera Connection Test.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

탈거

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. 정비 모드를 활성화합니다. 참조 항목: 정비 모드(활성화 및 비활성화).
  3. Partially open the liftgate.
    Informational PurposesAn informational icon, calling your attention
    참고
    Allow the liftgate to open fully, and then pull the liftgate back to a comfortable working height.
  4. Apply masking tape around the liftgate applique to protect the painted surrounding area.
  5. Remove the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)
  6. Remove the liftgate applique bracket.
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull the bracket using the handle opening rearwards until the tabs back off from the liftgate.
  7. Disconnect the rear facing camera electrical connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    Push to lift the tab, and then disconnect the electrical connector.
  8. Remove the bolts (x2) that attach the rear facing camera to the liftgate applique bracket, and then remove the camera from the bracket.
    0.8 Nm (7 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)

장착

  1. Carefully remove the old double sided tape, clean the body surface with Isopropyl Alcohol (IPA) wipes, and then install new double sided tape.
  2. Install the bolts (x2) that attach the rear facing camera to the liftgate applique bracket.
    0.8 Nm (7 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)
  3. Secure the rear facing camera electrical connector on the liftgate applique bracket, and then connect the camera electrical connector.
  4. Unlock the vehicle gateway. See .
  5. Run PROC_DAS_X_CLEAR-CALIBRATIONvia Service Mode:
    • Driver Assist ➜ Cameras ➜ Clear Camera Calibration
    • Driver Assist ➜ Driverless ➜ Clear Calibration
    via Toolbox:(link)
  6. Run PROC_DAS_X_UPDATE-CAMERAvia Service Mode:Driver Assist ➜ Cameras ➜ Update Cameravia Toolbox:(link)
  7. Exit Service Mode.
  8. Install the liftgate applique bracket.
    1. Peel off the new double sided tape.
    2. Align the tabs to the liftgate holes, and then push the bracket into position.
    3. Apply pressure on the applique to help with the tape and bracket mating.
  9. Install the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)
  10. Remove all masking tape from the vehicle after 5 minutes for the applique to properly adhere to the liftgate.
  11. Close the liftgate.
  12. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.