교정 코드 44015142 0.30 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.

1. Open LH front door
2. Lower LH front window
3. Open LH rear door
4. Fold 60 seat into down position
   참고

   Seat can be folded from the backrest button or trunk switch, If seat cushion is not present, protect the seat as required

   

5. Open liftgate
6. Remove parcel shelf

   

7. Remove trunk load floor

   

8. Remove side load floor trim

   

9. Remove the trunk sill panel
   참고

   6x clips, 4x guides. Corners or bottom edge are good grabbing points for removal, Can use plastic trim tool or just your hands

   

   

   

10. Open charge port door using UI
    참고

    Controls > Charging > Open Charge Port

    

11. Open hood
    참고

    Via Center Display > Controls > Frunk Open

    

    

12. Remove rear underhood apron
    참고

    8x clips

    

    

13. Disconnect LV power. See LV 전원(연결 해제 및 연결).
14. Perform the charge port voltage check procedure. See 충전 포트 전압 점검.
15. Remove rear wall trim
    참고

    4x push clips, 2x datums

    

    

    

16. Remove LH trunk bracket assembly
    참고

    4x clips, 1 datum, Pull bracket straight up

    

    

    

17. Remove rear trunk floor

    

    

18. Remove LH side bolster trim
    참고

    1x clip, 1x tab, Start by releasing upper portion

    

    

    

19. Separate LH C-pillar trim from LH upper C-pillar trim
    참고

    4x clips, 4x datums

    

    

    

20. Release LH upper C-pillar trim and move aside
    참고

    7x clips

    

    

    

21. Release clips securing LH trunk side trim and remove
    참고

    3x push clips, 3x clips, 2x connectors

    

    

    

    

22. Remove charge port safety cap
    참고

    3x tabs

    

    

    

23. Install charge port safety cap
    참고

    3x tabs, Safety cap will click into position

    

    

    

    

24. Install LH trunk side trim and secure clips
    참고

    3x push clips, 3x clips, 2x connections

    

    

    

    

25. Install LH upper C-pillar trim
    참고

    7x clips, Replace any damaged clips

    

    

    

26. Secure LH C-pillar trim onto LH upper C-pillar trim
    참고

    4x clips, 4x datums, Replace any damaged clips, Verify seated properly

    

    

    

27. Install LH side bolster trim
    참고

    1x clip, 1x tab, Replace clip if damaged, Hook bottom portion and then secure the top

    

    

28. Install rear trunk floor

    

    

29. Install LH trunk bracket assembly
    참고

    4x clips, 1 datum

    

    

    

30. Install rear wall trim
    참고

    4x push clips, 2x datums

    

    

    

31. Install trunk sill panel
    참고

    6x clips, 4x guides

    

    

    

32. Install side load floor

    

33. Install trunk load floor

    

34. Install parcel shelf

    

35. Close liftgate
36. Fold 60 seat into vertical position
    참고

    Remove seat cushion protection

    

    

37. Close LH rear door
38. Connect First Responder Loop and LV battery connector
    참고

    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

    

39. Install rear underhood apron
    참고

    8x clips

    

    

40. Close hood
    참고

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

41. Raise LH front window
42. Close LH front door