2026-07-31

LH Clevis Motor Mount and RH Bushing Carrier - Set (Remove and Replace)

교정 코드 39010102302 FRT 6.40 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  • 2026-03-06: Released new procedure.

탈거

  1. Remove the front drive unit. See 구동 장치 - 전면(탈거 및 장착)
  2. Release bolts securing RHS bushing carrier and remove assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, EP20, 60 Nm + 50 Degrees, Verify FDU strap is secured properly, Recommend assistance to prevent unit from tilting
  3. Install RHS bushing carrier and secure bolts
    Informational PurposesAn informational icon, calling your attention
    참고
    4x bolts, EP20, 60 Nm + 50, Verify FDU strap is secured properly, Recommend assistance to prevent unit from tilting, Torque bolts down in the sequence shown
  4. Remove bolts from LH FDU clevis mount to body
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E14, 65 Nm
  5. Release bolts securing clevis to LH motor mount assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E14, 92 Nm
  6. Release bolts securing LH motor mount assembly to FDU
    Informational PurposesAn informational icon, calling your attention
    참고
    3x bolts, E14, 35 Nm + 55 degrees
  7. Separate clevis mount from LH motor mount assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E14, 92 Nm

장착

  1. Install bolts securing LH motor mount assembly to FDU
    Informational PurposesAn informational icon, calling your attention
    참고
    3x bolts, E14, 35 Nm + 55 degrees, Install bolts and perform final torque in the sequence shown
  2. Position the FDU assembly under the vehicle for installation
  3. Raise the FDU into the vehicle
    Informational PurposesAn informational icon, calling your attention
    참고
    Recommend assistance, Keep harnesses and hoses clear of FDU during install
  4. Loosely install bolts securing LH FDU mount to body
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E14, 65 Nm
  5. Install bolts securing clevis to LH motor mount assembly
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E14, 92 Nm, Center clevis mount and torque bolts
  6. Raise the FDU until the front fastener securing RH FDU mount to the body can be installed
    Informational PurposesAn informational icon, calling your attention
    참고
    Visually inspect holes are aligned
  7. Loosely install the front fastener securing the RH FDU mount to the body
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, EP20, 120 Nm, Torque at later step
  8. Install bolt securing rear of RH FDU mount
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, EP20, 120 Nm
  9. Torque bolt securing front of RH FDU mount to body
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, EP20, 120 Nm
  10. Fully secure bolts securing LH FDU mount to body
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, E14, 65 Nm
  11. Install the front drive unit. See 구동 장치 - 전면(탈거 및 장착)