2023-08-16

페시아 어셈블리 - 후면(HW4)(탈거 및 교체)

Correction code 10013012 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure.NOTE: See 인체공학적 주의 사항for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

탈거

  1. Remove the rear fascia assembly. See 페시아 어셈블리 - 후방(탈거 및 장착).
  2. Remove the screws (x2) that attach the LH rear BLE assembly to the rear fascia, and then remove the assembly from the fascia. Repeat this step for the RH rear BLE assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
    그림 1. LH shown; RH similar
    그림 2. LH shown; RH similar
  3. Remove the top LH and RH bolts that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    그림 3. LH shown; RH similar
  4. Position the rear fascia assembly upside down on workbench.
  5. Remove the screws (x2) and release the tabs (x10) that attach the tow hitch cover to the rear fascia assembly, and then remove the cover from the assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Large flathead screwdriver
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Plastic screws are captive. Be careful to avoid damage.
  6. Remove the bottom bolts (x6) that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  7. Position the rear fascia assembly upright on the workbench.
  8. Release the tabs (x8) that attach the rear diffuser to the rear fascia assembly, and then remove the diffuser from the assembly.
  9. Remove the bolts (x2) that attach the rear lower fascia to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  10. Release the tabs (x23) that attach the rear lower fascia to the rear fascia assembly, and then remove the lower fascia from the assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Insert a pick behind the lower fascia tab, and the rotate to pry the fascia assembly tab upward.

장착

  1. Place the new rear fascia assembly upside down on flat and protected surface.
  2. Position the rear lower fascia onto the rear fascia assembly, and then secure the tabs (x23) that attach the lower fascia to the assembly.
    그림 4. LH shown; RH similar
  3. Place the rear fascia assembly upright on the workbench.
  4. Install the bolts that attach the rear lower fascia to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  5. Position the rear diffuser onto rear fascia assembly, and then secure the tabs (x8) that attach the diffuser to the fascia.
  6. Install the top LH and RH bolts that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    그림 5. LH shown; RH similar
  7. Place the rear fascia assembly upside down on workbench.
  8. Install the bottom bolts (x6) that attach the rear diffuser to the rear fascia assembly.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  9. Position the tow hitch cover onto the rear fascia assembly, and then secure the tabs (x10) that attach the cover to the fascia.
  10. Install the bolts that attach the tow hitch cover to the rear fascia.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Large flathead screwdriver
    Informational PurposesAn informational icon, calling your attention
    참고
    Plastic screws are captive. Be careful to avoid damage.
  11. Place the rear fascia assembly upright on workbench.
  12. Position the RH rear BLE assembly onto the rear fascia, and then install the screws that attach the BLE assembly to the fascia. Repeat this step for the LH BLE assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
    그림 6. LH shown; RH similar
  13. Install the rear fascia assembly. See 페시아 어셈블리 - 후방(탈거 및 장착).