교정 코드 17107702 17107802 0.36 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

1. Open LH front door

   

2. Raise and support vehicle
   참고

   Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads

   

   

   

3. Open hood
   참고

   Select Controls > Frunk Open

   

   

4. Remove rear underhood apron
   참고

   8x clips

   

   

5. Remove LH underhood apron
   참고

   10x clips

   

   

6. Remove RH underhood apron
   참고

   10x clips

   

   

7. Remove front underhood apron
   참고

   7x clips

   

   

8. Remove frunk access panel
   참고

   3x clips, 3x hooks, 1x connector

   

   

9. Remove frunk carpet

   

   

10. Remove frunk assembly
    참고

    4x bolts, 10mm, 5 Nm

    

    

11. Disconnect active noise cancellation harness connector from frunk harness
    참고

    1x connector, Release locking tab, 1x harness clip, Release clip securing active noise cancellation harness connector onto body

    

    

    

12. Remove LH front wheel cap
    참고

    Lift every other spoke at a time until cap is released from rim

    

    

    

13. Loosen LH front wheel
    참고

    5x nuts, 21mm, 175 Nm

    

    

14. Raise vehicle partially and lower onto locks
    참고

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

15. Remove LH front wheel
    참고

    5x nuts, 21mm, 175 Nm

    

    

16. Release clips securing active noise cancellation harness onto bracket
    참고

    2x harness clip

    

    

17. Disconnect active noise cancellation harness connector from sensor and remove harness from vehicle
    참고

    1x connect, Release locking tab

    

18. Connect active noise cancellation harness onto sensor
    참고

    1x connect, Secure locking tab

    

19. Position active noise cancellation harness into place
    참고

    Ensure the harness is routed above the lower links and below the tie rod and halfshaft

    

    

20. Install clips securing active noise cancellation harness onto bracket
    참고

    2x harness clip

    

    

21. Install LH front wheel
    참고

    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

    

    

22. Lower vehicle until tires are touching ground
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

    

23. Torque LH front wheel
    참고

    5x nuts, 21mm, 175 Nm

    

    

24. Install LH front wheel cap
    참고

    Align valve stem with cap

    

    

25. Connect active noise cancellation harness connector to frunk harness
    참고

    1x connector, Secure locking tab, 1x harness clip, Install clip securing active noise cancellation harness connector onto body

    

    

    

26. Install frunk assembly
    참고

    4x bolts, 10mm, 5 Nm

    

    

27. Install frunk carpet
    참고

    Verify carpet is properly seated under the seal

    

    

28. Install frunk access panel
    참고

    3x clips, 3x hooks, 1x connector

    

    

29. Install front underhood apron
    참고

    7x clips

    

    

30. Install RH underhood apron
    참고

    10x clips

    

    

31. Install LH underhood apron
    참고

    10x clips

    

    

32. Install rear underhood apron
    참고

    8x clips

    

    

33. Close hood
    참고

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

    

34. Remove vehicle from lift
    참고

    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"

    

    

35. Close LH front door
    참고

    Close doors