2025-11-22

페시아 어셈블리 - 전면(HW4)(탈거 및 교체)

교정 코드 10011032 0.72 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-11-17: Replaced radar heater disconnect step with reference to rework procedure. Removed steps to reinstall and reconnect radar heater.
  • 2023-08-24: Added steps to transfer the front license plate brackets from the old fascia to the new fascia.

탈거

  1. Remove the front license plate base bracket and front license plate molding painted bracket from the old front fascia so that they can be installed on the replacement fascia in a later step. See 베이스 브래킷 - 번호판 - 전면(탈거 및 교체).
  2. Remove the front fascia assembly. See 페시아 어셈블리 - 전면(탈거 및 장착).
  3. Disconnect the LH front fog light electrical connector. Repeat this step for the RH fog light electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull again to release the headlight electrical connector.
  4. Remove the LV jumper wires (x2) from the tow hook cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    Squeeze the retaining tabs together and gently remove the jumper wires from the tow hook cover.
  5. Disconnect the front Bluetooth Low Energy (BLE) module electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull again to release the BLE electrical connector.
  6. If the radar heater has not been permanently disconnected, perform the rework. See 히터 - 레이더(재작업)(2021년 7월 1일 이전에 제조된 차량) or 히터 - 레이더(재작업)(2021년 7월 1일 이후에 제조된 차량).
  7. Disconnect the pedestrian warning speaker electrical connector, and then release the electrical harness from the edge clip that is located on the RH side of the front fascia valance.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull again to release electrical connector.
  8. Release the clips (x10) that attach the electrical harness to the front fascia assembly, and then remove the electrical harness from the fascia.
  9. Remove the screws (x3) that attach the RH front fog light to the front fascia assembly. Repeat this step for the LH front fog light.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 비트
  10. Release the retaining tabs (x4) that attach the RH front fog light, and then remove the RH front fog light from the front fascia assembly. Repeat this step for the LH front fog light.
  11. Remove the push clips (x8) that attach the valance to the front fascia assembly.
  12. Remove the nuts (x2) that attach the valance to the front fascia assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    Release the LH and RH corners of the valance from the front fascia assembly.
  13. Remove the screws (x2) that attach the front fascia grille to the front fascia assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 비트
  14. Release the tabs (x11) that attach the front fascia grille to the front fascia assembly, and then remove the grille from the fascia.
  15. Remove the screw that attaches the T badge support to the front fascia assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 비트
  16. Release the tabs (x4) that attach the T badge support to the front fascia assembly, and then remove the T badge support from the fascia.

장착

  1. Put the new front fascia assembly on a padded workbench.
  2. Fasten the tabs (x4) that attach the T badge support to the front fascia assembly.
  3. Install the screw that attaches the T badge support to the front fascia assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 비트
  4. Fasten the tabs (x11) that attach the front fascia grille to the front fascia assembly.
  5. Install the screws (x2) that attach the front fascia grille to the front fascia assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 비트
  6. Install the nuts (x2) that attach the valance to the front fascia assembly.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
    Informational PurposesAn informational icon, calling your attention
    참고
    Interlock valance tabs with fascia tabs.
    Informational PurposesAn informational icon, calling your attention
    참고
    Secure the LH and RH corners of the valance to the front fascia assembly.
  7. Fasten the push clips (x8) that attach the valance to the front fascia assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Hold the front fascia tabs flush with valance, if necessary.
  8. Fasten the retaining tabs (x4), and then install the screws (x3) that attach the LH front fog light. Repeat this step for the RH front fog light.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Torx T25 비트
  9. Fasten the clips (x10) that attach the electrical harness to the front fascia assembly.
  10. Connect the pedestrian warning speaker electrical connector, and then secure it with the edge clip.
    Informational PurposesAn informational icon, calling your attention
    참고
    Engage the locking tab.
    Informational PurposesAn informational icon, calling your attention
    참고
    The edge clip is located on the RH ride of the front fascia valance.
  11. Connect the front BLE module electrical connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    Engage the locking tab.
  12. Install the LV jumper wires (x2) to the tow hook cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure that both wire terminals are fully seated behind the retaining tabs.
  13. Connect the LH front fog light electrical connector. Repeat this step for the RH side.
    Informational PurposesAn informational icon, calling your attention
    참고
    Engage the locking tab.
  14. Install the front fascia assembly. See 페시아 어셈블리 - 전면(탈거 및 장착).
  15. Install the front license plate base bracket and front license plate molding painted bracket that was removed from the old fascia onto the new fascia. See 베이스 브래킷 - 번호판 - 전면(탈거 및 교체).