2024-02-11

사이드 리피터 - 전면 - LH(HW4)(탈거 및 교체)

Correction code 17403702 0.12 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.

  • 2024-02-05: Added a caution to wrap the terminals of the camera and wiring harness to prevent them from coming into contact with water or other solutions that could cause damage.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

탈거

  1. Apply masking tape to the LH front fender assembly at the edges of the LH front side repeater.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Masking tape
  2. Release the push clip that attaches the LH front side repeater to the LH front fender assembly.
    그림 1. Inside fender view is for clarity only and access is not required for procedure
    1. Apply light constant pressure towards the fender at the rear of the side repeater, and keep pressure applied until the side repeater is released from the fender.
    2. Slide the side repeater approximately 5 mm towards the rear of the vehicle until the front clip is clear of the fender.
    3. Pull the front end of the side repeater away from the fender until the front clip releases from the fender.
    4. Slide the side repeater towards the front of the vehicle until the rear hook clip releases from the fender.
  3. Disconnect the LH front side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    참고
    Press down on the lock release and pull the connector away from the side repeater camera. Release the red locking tab and press down to disconnect the side repeater connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Wrap the terminals of the camera and wiring harness to prevent them from coming into contact with water or other solutions that could cause damage.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • Pocket screwdriver
  4. Remove the LH front side repeater from the vehicle.
  5. Remove the LH front side repeater camera. See 사이드 리피터 카메라 - 전면 - LH(HW4)(탈거 및 교체).

장착

  1. Install the LH front side repeater camera. See 사이드 리피터 카메라 - 전면 - LH(HW4)(탈거 및 교체).
  2. Connect the LH front side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    참고
    Remove the tape first, if present.
    Informational PurposesAn informational icon, calling your attention
    참고
    Secure the side repeater connectors, and then engage the red locking tab on the side repeater connector.
  3. Open the LH front door.
  4. 드라이버 어시스턴스 시스템(DAS)을 리셋합니다.
    1. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
    2. 터치스크린 정비 모드 메뉴에서 Driver Assist > Cameras > Reset DAS를 터치합니다.
    3. 터치스크린 카메라 다이어그램에서 다음을 확인하십시오. DAS 초기화 버튼이 녹색으로 강조 표시되고 모든 DAS 구성품이 녹색 상태 표시등을 표시합니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      빨간색 상태 표시등이 표시된 DAS 구성품을 모두 살펴보고 수정합니다.
  5. Close the LH front door.
  6. Install the push clip that attaches the LH front side repeater to the LH front fender assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure all tabs are intact and installed in place correctly.
    1. Insert the side repeater rear hook clip into the repeater slot in the fender, apply light constant pressure at the rear of the repeater, and then keep pressure until the repeater is installed.
    2. Slide the side repeater rearwards until the rear hook clip engages the fender and the front clip clears the edge of the repeater slot in the fender.
    3. Press on the front of the side repeater until the front clip is inside of the repeater slot and keep pressure on the front and rear of the repeater until installation is complete.
    4. Slide the side repeater towards the front of the vehicle until the front clip engages the fender, and then release pressure on the repeater.
  7. Remove the masking tape from the LH front fender assembly at the edges of the LH front side repeater.