2026-11-03

Innfatning – ratt (fjerne og skifte ut)

Korrigeringskode 32051812 0.36 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og dens tilhørende FRT alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

  • 2026-11-03: Updated the specification of the bolts (x4) that attach the bright surround to the steering wheel.
  • 2026-08-10: Added batch information about the bolts (x4) that attach the bright surround to the steering wheel.

Dreiemomentspesifikasjoner

Table 1. Dreiemomentspesifikasjoner: Eikedeksel – ratt – nedre (fjerne og skifte ut) / Innfatning – ratt (fjerne og skifte ut)
Beskrivelse Dreiemomentverdi Anbefalte verktøy Bruke på nytt / skifte ut Merknader
Bolts (x4) that attach the bright surround to the steering wheel
2.5 Nm (1.8 lbs-ft)
1.8 Nm (1.3 lbs-ft)
  • Torx T25 bit
  • PH1 Stubby Phillips Screwdriver
 Bruke på nytt

T25 bolts: 2.5 Nm

PH1 bolts: 1.8 Nm
Bolts that attach the LH/RH steering wheel switch/steering controller/lower spoke cover to the bright surround
0.9 Nm (8 lbs-in)
  • Torx T10 bit
Bruke på nytt

Fjerne

  1. Disconnect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  2. Remove the driver airbag. See Kollisjonspute – fører (fjerne og skifte ut).
  3. Disconnect the steering wheel electrical wiring harness connector.
  4. Disconnect the electrical harness from the LH steering wheel switch connector.
  5. Disconnect the electrical harness from the RH steering wheel switch connector.
  6. Release the clips that attach the horn assembly, and then move the horn assembly to the side.
  7. Disconnect the electrical harness from the lower connector, and then remove the electrical harness from the steering wheel.
  8. Remove the bolts (x4) that attach the bright surround to the steering wheel.
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Pry the lower portion of the bright surround assembly away from the steering wheel, and then work your way around. Do not remove it now. Wait until the steering wheel is removed.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  9. Remove the bolts (x3) that attach the LH steering wheel switch to the bright surround, and then remove the switch from the surround.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  10. Remove the bolts (x3) that attach the RH steering wheel switch to the bright surround, and then remove the switch from the surround.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  11. Remove the bolts (x2) that attach the steering wheel controller to the steering wheel surround, and then remove the controller.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  12. Remove the bolts that attach the lower spoke cover to the steering wheel surround.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit

Montere

  1. Position the lower spoke cover onto the steering wheel surround, and then install the bolts.
    0.9 Nm (8 lbs-in)
    Note
    Insert the lower edge of the lower spoke.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  2. Install the bolts that attach the steering wheel controller to the steering wheel surround.
    0.9 Nm (8 lbs-in)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  3. Position the LH steering wheel switch onto the steering wheel surround, and then install the bolts.
    0.9 Nm (8 lbs-in)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  4. Position the RH steering wheel switch onto the steering wheel surround, and then install the bolts.
    0.9 Nm (8 lbs-in)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T10 bit
  5. Position the steering wheel surround onto the steering wheel, and then install the bolts.
    2.5 Nm (1.8 lbs-ft)
    1.8 Nm (1.3 lbs-ft)
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Torque the T25 bolts to 2.5 Nm; torque the PH1 bolts to 1.8 Nm.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  6. Position the horn to the steering wheel assembly, and then fasten the clips.
  7. Connect the LH steering wheel switch electrical connector.
  8. Connect the RH steering wheel switch electrical connector.
  9. Connect the lower connection to the steering wheel controller.
  10. Connect the steering wheel electrical wiring harness connector.
  11. Install the driver airbag. See Kollisjonspute – fører (fjerne og skifte ut).
  12. Connect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).