2025-08-21
Bremselinjer – hovedsylinder til ABS (uten strukturell pakke) (høyrestyrt) (fjerne og skifte ut)
Korrigeringskode
33034202 2.04
MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.
MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til ServiceManualFeedback@tesla.com.
MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.
- 2025-06-26: Modified brake bleeding method to bleed through inner valves only.
Fjerne
- Open the RH front door and lower the RH front window.
- Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
- Remove the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
- Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
- Remove the 12V battery. See 12 V-/lavspenningsbatteri (fjerne og skifte ut).
- Remove the fresh air intake duct. See Kanal – HEPA (fjerne og skifte ut).
- Remove the front aero shield. See Panel – luftskjerm – foran (Uten strukturell pakke)(fjerne og skifte ut).
-
Remove the fir tree clips (x4) that attach the coolant hoses to the AC compressor bracket.
-
Remove the retaining clips (x2) that attach the AC compressor HV harness to the shock tower brace.
-
Remove the LH and RH bolts that attach the shock tower brace to the body.55 Nm (40.6 lbs-ft)55 Nm (40.6 lbs-ft)
-
Remove the LH and RH outer bolts that attach the shock tower brace to the body.62 Nm (45.7 lbs-ft)
-
Disconnect the HVIL connector.
-
Remove the bolts (x2) that attach the AC compressor bracket to the shock tower brace.
31 Nm (22.9 lbs-ft)
-
Carefully remove the AC compressor and AC compressor bracket towards the front of the vehicle, under the shock tower brace.
- Disconnect the electrical connector from the ABS unit.
- Position the oil drain under the ABS unit.
-
Loosen the nut that attaches the master cylinder secondary brake line to the ABS unit.
16 Nm (11.8 lbs-ft)
-
Loosen the nut that attaches the primary cylinder secondary brake line to the ABS unit.
16 Nm (11.8 lbs-ft)
- Place an absorbent material beneath the brake booster and reservoir area.
- Using a brake fluid syringe, remove the brake fluid from the reservoir.
-
Loosen the nut that attaches the secondary brake line to the master cylinder, and then remove the secondary brake line.
16 Nm (11.8 lbs-ft)
-
Loosen the nut that attaches the primary brake line to the master cylinder, and then remove the primary brake line.
16 Nm (11.8 lbs-ft)
-
Release the primary and secondary brake lines from the brake line bundle clip.
-
Remove the bolts (x2) that attach the ABS unit to the frame rail.
10 Nm (7.4 lbs-ft)
- Move the ABS unit and bracket towards the 12V battery area to make sure there is space to remove the brake lines.
-
Remove the brake lines from the bundle clips (x2) under the ABS unit.
-
Remove and discard the bolts (x2) that attach the harness guide to the front controller, and then release the harness guide.
6 Nm (4.4 lbs-ft)
-
Remove brake line bundle clips (x3).
- Route the master cylinder brake lines towards the right controller, and then remove the master cylinder brake line bundle from the vehicle.
Montere
- Route the master cylinder brake lines from the controller towards the ABS unit, and then put the brake lines into position.
-
Install the brake line bundle clips (x3).
-
Mount the brake lines to the bundle clips (x2)under the ABS unit.
-
Fasten the bolts (x2) that attach the harness guide to the front controller.
MerkReplace the patchbolts.6 Nm (4.4 lbs-ft)
-
Mount the primary and secondary brake lines to the brake line bundle clip.
-
Fasten the nut that attaches the master cylinder secondary brake line to the ABS unit.
16 Nm (11.8 lbs-ft)
-
Fasten the nut that attaches the primary cylinder secondary brake line to the ABS unit.
16 Nm (11.8 lbs-ft)
- Clean the ABS unit surface of residual brake fluid.
-
Put the ABS unit and bracket into position.
- Remove the oil drain container from underneath vehicle
-
Install the bolts (x2) that attach the ABS unit to the frame rail.
10 Nm (7.4 lbs-ft)
-
Install the secondary brake line to the master cylinder, and then fasten the nut that attaches the secondary brake line.
16 Nm (11.8 lbs-ft)
-
Install the primary brake line to the master cylinder, and then fasten the nut that attaches the primary brake line.
16 Nm (11.8 lbs-ft)
- Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
-
Carefully position the AC compressor and AC compressor bracket into the vehicle.
-
Fasten the bolts (x2) that attach the AC compressor bracket to the shock tower brace.
31 Nm (22.9 lbs-ft)
-
Install the fir tree clips (x4) that attach the coolant hoses to the AC compressor bracket.
-
Install the LH and RH bolts that attach the shock tower brace to the body.55 Nm (40.6 lbs-ft)55 Nm (40.6 lbs-ft)
-
Install the LH and RH outer bolts that attach the shock tower brace to the body.62 Nm (45.7 lbs-ft)
-
Install the retaining clips (x2) that attach the AC compressor HV harness to the shock tower brace.
-
Connect the HVIL connector
- Install the 12V battery. See 12 V-/lavspenningsbatteri (fjerne og skifte ut).
- Reconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
- Install the fresh air intake duct. See Kanal – HEPA (fjerne og skifte ut).
- Install the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
-
Luft venstre og høyre bremsekalipere foran gjennom bremsekalipernes innvendige lufteventiler til ren væske uten luftbobler strømmer ut av kaliperen.
MerkDet er ikke nødvendig å lufte ut bremsekaliperne gjennom de utvendige lufteventilene.
- Skyll kaliperen foran til venstre ved hjelp av den innvendige lufteventilen til du observerer en merkbar reduksjon i luftbobler.
- Skyll kaliperen foran til høyre ved hjelp av den innvendige lufteventilen til du observerer en merkbar reduksjon i luftbobler.
- Luft ut kaliperen foran til venstre ved hjelp av den innvendige lufteventilen. Se Lufte/skylle bremsevæske for mer informasjon.
- Luft ut kaliperen foran til høyre ved hjelp av den innvendige lufteventilen. Se Lufte/skylle bremsevæske for mer informasjon.
- Sørg for å utføre testen av bremsestivhet. Se Lufte/skylle bremsevæske for mer informasjon.
- Install the front aero shield. See Panel – luftskjerm – foran (Uten strukturell pakke)(fjerne og skifte ut).
- Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
-
Gjennomfør en kjøretest med en rekke aggressive bremsinger for å forsikre deg om at pedalfølelsen og bremseytelsen er som den skal.
MerkLegg til korrigeringskode 00040100 for prøvekjøring som en egen aktivitet for servicebesøket.