Slange – omformer til varmeveksler – bakre drivenhet (3DU) (fjerne og skifte ut)
Korrigeringskode
18300192 1.92
MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.
MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til ServiceManualFeedback@tesla.com.
MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.
- 2025-04-04: Cleaned up procedure for clarity, updated ODIN routines.
- 2023-06-09: Added shear plate small bolts torque figure for Structural Pack vehicles.
1781872-02-A M3/Y REAR AXLE DROP ASSIST KIT
Dreiemomentspesifikasjoner
Beskrivelse | Dreiemomentverdi | Anbefalte verktøy | Bruke på nytt / skifte ut | Merknader |
---|---|---|---|---|
Bolter som fester bremsekaliperbraketten bak til venstre til styreleddet |
![]() 83 Nm (61.2 lbs-ft) |
|
Erstatt | |
Bolter som fester demperen bak til venstre på det øvre festet |
![]() 41 Nm (30.2 lbs-ft) |
|
Bruke på nytt | |
Mutter som fester jordingsstroppen for den bakre drivenheten til karosseriet |
![]() 10 Nm (7.4 lbs-ft) |
|
Bruke på nytt | |
Mutre som fester høyspenningsbatteriet til ledningsnettbraketten for den bakre drivenheten til høyspenningsbatteriet |
![]() 10 Nm (7.4 lbs-ft) |
|
Bruke på nytt | |
Små bolter som fester den venstre skjærplaten til høyspenningsbatteriet (biler uten strukturell pakke) |
![]() 35 Nm (25.8 lbs-ft) |
|
Bruke på nytt | |
Små bolter som fester den venstre skjærplaten til høyspenningsbatteriet (biler med strukturell pakke) |
![]() 62 Nm (45.7 lbs-ft) |
|
||
Stor bolt som fester den venstre skjærplaten og den bakre underrammen til karosseriet |
![]() 130 Nm (95.9 lbs-ft) |
|
Erstatt | |
Bolter som fester den bakre underrammen til karosseriet |
![]() 165 Nm (121.7 lbs-ft) |
|
Erstatt |
Remove
- Prepare the vehicle for lifting. See Heve bil – løftebukk med 2 stolper.
-
Utfør følgende rutine med Servicemodus eller Toolbox (se 0005 – Servicemodi):
PROC_VCFRONT_X_START-THERMAL-FILL-DRAINvia Toolbox: (link)via Service Mode:
- Thermal ➜ Actions ➜ Start Thermal Fill/Drain
- Thermal ➜ Coolant System ➜ Start Coolant Fill/Drain
- Thermal ➜ Refrigerant System ➜ Start Refrigerant Fill/Drain
- Disconnect 12V/LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
- Perform the vehicle HV disablement procedure. See Deaktiveringsprosedyre for bilens høyspenning.
- Remove the LH and RH rear wheels. See Hjulenhet (fjerne og skifte ut).
- Remove the LH and RH suspension cover. See Deksel – fjæring bak – venstre (fjerne og skifte ut).
- Remove the mid aero shield panel. See Panel – luftskjerm – bakre (fjerne og skifte ut).
- Remove the rear fascia diffuser. See Diffuser – bakfanger (fjerne og skifte ut).
- Disconnect the RH side 12V subframe harness connector.
- Remove the RH side 12V subframe harness clip from the body.
- Disconnect the electrical harness from the LH 12V subframe connector.
- Release the clip that attaches the LH subframe electrical harness to the body.
-
Remove the nut that attaches the rear
drive unit ground strap to the body.
TIpBruk av følgende verktøy anbefales:
- 10 mm 12 pkt. pipenøkkelinnsats
- Remove the rear stabilizer bar. See Krengestabilisator – bak (fjerne og skifte ut).
- Release the clips (x2) that attach the coolant hoses to the LH shear plate.
-
Release the LH side hose clips from
the rear battery skid plate.
MerkNumber of clips may vary depending on vehicle built date.
- Release the RH side hose clips from the rear battery skid plate.
- Release the clips (x2) that attach the coolant hoses to RH shear plate.
- Position a coolant drain container underneath the LH RDU area.
-
Disconnect the RDU inverter inlet hose
from the fluid coupling.
MerkPlug ends as needed.
- Remove the coolant drain container from underneath the vehicle.
-
Release the RDU inverter inlet tube
from the RDU HV cable harness.
Merk1x fir tree clip
- Remove the bolt that attaches the RDU HV cable bracket to the RDU.
- Disconnect the RDU HV connector from the RDU.
-
Perform the RDU diode test.
MerkMake sure that the RDU HV cable is disconnected from the HV battery.
Use a multimeter in diode mode, with the positive DMM probe to B- of the inverter and the negative probe to B+.
Pin #1 on HV cables is B- and Pin #2 is B+.
MOSFET acceptable diode reading:1.0 - 2.0 V. IGBT acceptable diode reading 0.45 - 2 V (if you get OL or > 2V for a reading you most likely have the probes installed the wrong way around)
-
Release the RDU logic connector.
MerkDo not allow coolant to enter the connector. Move connector aside as needed.
-
Release the RDU logic connector
clip.
Merk1x clip
- Place subframe lifting tool into position underneath the rear subframe.
-
Raise subframe lifting tool to support
the rear subframe
Merk3x straps. Attach metal hooks at the end of the straps to the rings on the subframe lifting tool and pull straps until they are secure. Lower the vehicle as necessary, Assistance is recommended.
- Remove the smaller bolts (x2) that attach the LH shear plate.
- Remove the large bolt that attaches the LH shear plate and subframe to the body, and then remove the shear plate.
-
Install the LH front extension bolt to
secure the subframe to the body.
MerkDuring lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height.
- Repeat steps 30to 32 on the RH side of the vehicle.
- Remove the LH rear bolt that attaches the subframe to the body.
-
Install the LH rear extension bolt t0
secure the subframe to the body.
MerkDuring lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height as possible
- Remove the RH rear bolt that attaches the subframe to the body.
-
Install the RH rear extension bolt to
secure the subframe to the body.
MerkDuring lowering and raising the sub frame, the adjusting nut and the other three nuts should be kept at the same height.
-
Partially lower the subframe and rear
drive unit assembly.
MerkUse caution while lowering subframe to avoid damage to surrounding components. Lower the subframe approximately 13 cm.
- Release the clip that attaches the inverter to heat exchanger hose to the inverter and remove the hose from the inverter.
- Release the clips (x4) that attach the inverter coolant hose to the RDU.
- Release the RDU inverter coolant hose from the heat exchanger, and the remove the hose from the vehicle.
-
Install the inverter to heat exchanger
hose to the heat exchanger.
MerkPerform a push-pull-push test to make sure that the hose is fully seated.
- Install the clips (x4) that attach the inverter to heat exchanger coolant hose to the RDU.
-
Install the inverter to heat exchanger
hose to the inverter.
MerkPerform a push-pull-push test to make sure hose is fully seated.
- Raise drive unit and subframe into position.
- Remove the RH rear extension bolt.
-
Install the RH rear bolt that attaches
the rear subframe to the body hand tight.
MerkTorque at a later step.
- Remove the LH rear extension bolt.
-
Install the LH rear bolt that attaches
the rear subframe to the body hand tight
MerkTorque at a later step.
- Remove the LH front extension bolt .
-
Install the large bolt and shear plate
to the LH side of the rear subframe hand tight.
MerkTorque at a later step
-
Install the smaller bolts (x2) that
attach the LH rear shear plate to the body hand tight.
MerkTorque at a later step.
- Remove the RH front extension bolt.
-
Install the large bolt and shear plate
to the RH side of the rear subframe hand tight.
MerkTorque at a later step.
-
Install the smaller bolts (x2) that
attach the RH shear plate hand tight.
MerkTorque at a later step.
-
Torque the smaller bolts that attach
the LH and RH shear plates to the vehicle.
Merk35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles.
-
Torque the larger bolts that attach
the LH and RH rear shear plate to the body (torque 130 Nm).
Merk1x bolt, 21mm, 130 Nm, Mark bolt after torque
- Torque the bolt that attaches the RH rear of the subframe to the body (torque 165 Nm).
- Torque the bolt that attaches the LH rear of the subframe to the body (torque 165 Nm).
- Install the clips that attach the coolant hoses to the RH shear plate.
- Install the clips that attach the coolant hoses to the LH shear plate.
-
Lower the rear subframe lifting
tool.
MerkMake sure that the yellow safety straps are removed from the subframe.
- Remove the subframe lifting tool from underneath the vehicle.
- Attach the RDU logic connector clip.
-
Connect the RDU logic connector.
MerkMake sure that there is no spilled coolant inside the connector.
- Connect the RDU HV cable connector to the RDU.
- Install the bolt that attaches the RDU HV cable bracket to the RDU (torque 6 Nm).
-
Remove the hose plugs, and then
connect the coolant inlet hose to the rear drive unit.
MerkPerform a push-pull-push test to make sure that hose is fully seated.
- Install the RDU inverter inlet hose clip onto the HV cable.
- Install the RH side hose clips to the rear battery skid plate.
-
Install the LH side hose clips to the
HV battery rear skid plate enclosure.
MerkNumber of clips may vary per vehicle build date.
- Install the rear stabilizer bar. See Krengestabilisator – bak (fjerne og skifte ut).
-
Install the nut that attaches the rear
drive unit ground strap to the body.10 Nm (7.4 lbs-ft)TIpBruk av følgende verktøy anbefales:
- 10 mm 12 pkt. pipenøkkelinnsats
MerkReinstall the washer if the vehicle had this washer during removal. -
Install LH side 12V subframe harness
clip to body
Merk1x clip
-
Connect LH side 12V subframe harness
connector
Merk1x connector, Engage locking tab
- Install RH side 12V subframe harness clip to the body.
- Connect the RH side 12V subframe harness connector.
- Install the rear fascia diffuser. See Diffuser – bakfanger (fjerne og skifte ut).
- Install the mid aero shield panel. See Panel – luftskjerm – bakre (fjerne og skifte ut).
- Install the LH and RH rear suspension covers. See Deksel – fjæring bak – venstre (fjerne og skifte ut).
- Install the LH and RH rear wheels. See Hjulenhet (fjerne og skifte ut).
- Remove the coolant bottle cap, and then fill the coolant bottle to the "MAX" line.
- Connect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
-
Utfør følgende rutine med Servicemodus eller Toolbox (se 0005 – Servicemodi):
PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAINvia Toolbox: (link)via Service Mode:
- Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
- Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
- Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
- Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
- Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
- Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
- Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
- Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
- Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
-
Utfør følgende rutine med Servicemodus eller Toolbox (se 0005 – Servicemodi):
TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
- Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
- Thermal ➜ Coolant System ➜ Coolant Purge Start
- Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
- Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
- Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
- Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
- Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
- Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
- Inspect coolant level and top off as necessary.
-
Utfør følgende rutine med Servicemodus eller Toolbox (se 0005 – Servicemodi):
TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
- Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
- Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
- Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
- Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
- Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
- Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
- Exit Service Mode.
- Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
- Install the 2nd row lower seat cushion. See Setepute – nedre – andre rad (fjerne og skifte ut).
- Restore the driver and front passenger seats back to their original positions.
- Se tabellene for innrettingskrav for å avgjøre om en EPAS-innrettingskontroll (EC) eller kontroll av firehjulsinnstilling (AC) er nødvendig. Hvis nødvendig skal korrigeringskode for innrettingskontrollen/-justeringen legges til som en egen aktivitet for SV. Se Innrettingskrav – fjæring.