28/11/2023 18:18:58

Kollisjonsboks – øvre – foran – venstre (strukturell pakke) (fjerne og skifte ut)

Korrigeringskode 10012432 1,02 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Fjerne

Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Denne prosedyren er et UTKAST. Selv om den har blitt godkjent, kan det hende at advarsler og forholdsregler mangler. Følg sikkerhetskravene, og vær ytterst forsiktig ved arbeid på eller nær høyspenningssystemer og -komponenter. Send korrigeringer og tilbakemeldinger til ServiceDevelopment@teslamotors.com.
  1. Open the LH front door and lower the LH front window.
  2. Raise and support the vehicle. See Heve bil – løftebukk med 2 stolper.
  3. Use the touchscreen to place vehicle in service mode.
  4. Open the hood.
  5. Use the touchscreen to power off the vehicle.
  6. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  7. Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  8. Release the connector lock, and then disconnect the active grille shutter electrical connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Do not push down on the red tab. Pull the red tab to release the connector lock.
  9. Remove the ambient temperature sensor cover from the active grille shutter, and then disconnect the sensor electrical connector.
  10. Remove the bolts (x2) that attach the underhood storage unit reinforcement bracket to the cooling fan, and then slide the bracket rearward for clearance.
    Tips: Use of the following tool(s) is recommended:
    • External Torx Plus EP14
    • Skralle med fleksibelt hode / momentnøkkel med fleksibelt hode
    • 3 i forlengelse
  11. Remove the bolts (x5) that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Tips: Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • ¼ in std skralle
    • 2 i forlengelse
    • Wurth ¼ in sekskantet 1 Nm - 5 Nm momentnøkkel (kun montering)
      • ¼ in sekskantet til ¼ in kvadratisk 2 in adapter
  12. Remove the front aero shield panel. See Panel – luftskjerm – foran (Uten strukturell pakke) (fjerne og skifte ut).
  13. Remove the front fascia. See Støtfanger – foran (fjerne og montere).
  14. Raise vehicle fully and lower lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to comfortable working height. Make sure there's an audible click of locks on both sides before lowering, otherwise vehicle may tilt to side.
  15. Remove the cooling fan module. See Modul – kjølevifte (fjerne og montere).
  16. Lower vehicle partially and set lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered. Set vehicle to comfortable working height.
  17. Remove the front bumper beam. See Støtfangerbjelke – foran (fjerne og skifte ut).
    Informational PurposesAn informational icon, calling your attention
    Merk
    It is not necessary to remove the LH and RH front bumper crash accelerometer sensors or the foam from the bumper beam assembly after removing the assembly from the vehicle.
  18. Release the LH front upper crush can clip.
  19. Remove the bolt that attaches the LH front upper crush can to the vehicle.
    Tips: Bruk av følgende verktøy anbefales:
    • 13 mm nøkkel
  20. Remove and discard the bolts (x2) that attach the LH front upper crush can to the vehicle, and then remove the crush can from the vehicle.
    Tips: Bruk av følgende verktøy anbefales:
    • Cordless 3/8in Dr. Impact
    • Socket External Torx 3/8in Dr. EP16 - 1672283-00-A

Montere

  1. Position the LH front upper crush can on the vehicle, and then install the new bolts (x2) that attach the crush can to the vehicle.
    75 Nm (55.3 lbs-ft)
    Tips: Bruk av følgende verktøy anbefales:
    • Cordless 3/8in Dr. Impact
    • Skralle med fleksibelt hode / momentnøkkel med fleksibelt hode
    • Socket External Torx 3/8in Dr. EP16 - 1672283-00-A
  2. Install the bolt that attaches the LH front upper crush can to the vehicle.
    30 Nm (22.1 lbs-ft)
    Tips: Bruk av følgende verktøy anbefales:
    • 3 i forlengelse
    • 13 mm nøkkel
    • Cordless 3/8in Dr. Ratchet
    • Skralle med fleksibelt hode / momentnøkkel med fleksibelt hode
  3. Install the LH front upper crush can clip.
  4. Install the front bumper beam. See Støtfangerbjelke – foran (fjerne og skifte ut).
  5. Raise vehicle fully and lower lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to comfortable working height. Make sure there's an audible click of locks on both sides before lowering, otherwise vehicle may tilt to side.
  6. Install the cooling fan module. See Modul – kjølevifte (fjerne og montere).
  7. Lower vehicle partially and set lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered. Set vehicle to comfortable working height.
  8. Install the front fascia. See Støtfanger – foran (fjerne og montere).
  9. Raise vehicle fully and lower lift onto locks.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to comfortable working height. Make sure there's an audible click of locks on both sides before lowering, otherwise vehicle may tilt to side.
  10. Install the front aero shield panel. See Panel – luftskjerm – foran (Uten strukturell pakke) (fjerne og skifte ut).
  11. Install the bolts (x5) that attach the top of the front fascia to the vehicle.
    4 Nm (2.9 lbs-ft)
    Tips: Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • ¼ in std skralle
    • 2 i forlengelse
    • Wurth ¼ in sekskantet 1 Nm - 5 Nm momentnøkkel (kun montering)
      • ¼ in sekskantet til ¼ in kvadratisk 2 in adapter
  12. Position the underhood storage unit reinforcement bracket onto the cooling fan, and then install the bolts (x2) that attach the bracket to the fan.
    48 Nm (35.4 lbs-ft)
    Tips: Use of the following tool(s) is recommended:
    • External Torx Plus EP14
    • Skralle med fleksibelt hode / momentnøkkel med fleksibelt hode
    • 3 i forlengelse
  13. Connect the ambient temperature sensor electrical connector, and then install the sensor cover onto the active grille shutter.
  14. Connect the active grille shutter electrical connector, and then engage the connector lock.
  15. Remove the coolant bottle cap, and then fill the coolant to the "Max" line.
    Viktig: Ensure G-48 coolant is used.
  16. Connect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  17. Unlock vehicle gateway. See Gateway (lås opp).
  18. Use the touchscreen to access the thermal system routines.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Select Quick Controls > Service Mode > Thermal > Actions.
  19. Select "Start Coolant Air Purge".
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure the vehicle is not in "Drive". Putting the vehicle into "Drive" will stop this routine. Wait until the coolant pumps stop running (audible noise). "Routine Passed" will appear, but the pumps will run for approximately 10 minutes. If another routine is initiated during this time, it will fail. The routine is still running despite the completed message. Speeds can be monitored in garage under PT Thermal tab. Idle speed = ~1,500 RPM. The test will vary speeds from 3,500-6,500 RPM and actuate valves between SERIES and PARALLEL. If speeds hover at 7,000 RPM, this indicates the pumps are air locked. If the pumps are air locked, perform a coolant system vacuum fill (see Kjølesystem (vakuumfylling)), and then continue to add coolant and purge until the coolant level reaches between the NOM and MAX lines on the bottle.
  20. Inspect the coolant level and top off as necessary.
    Viktig: Ensure G-48 coolant is used.
  21. Install the coolant bottle cap.
  22. Perform the "Thermal Performance" routine through the touchscreen: Click "thermal icon" > Actions, then click Test Thermal Performance, and then Run. Close the window once the routine passes.
  23. Install the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
  24. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  25. Close the hood.
  26. Remove the vehicle from the lift.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Lower rack arms fully and remove from under the vehicle.
  27. Raise the LH front window.
  28. Close the LH front door.