03/06/2024 17:26:02

Bremselinjer – venstre dørstokk (Strukturell pakke) (fjerne og skifte ut)

Korrigeringskode 33035112 1.86 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

  • 2023-12-08: Updated brake stiffness routine.
Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Denne prosedyren er et UTKAST. Selv om den har blitt godkjent, kan det hende at advarsler og forholdsregler mangler. Følg sikkerhetskravene, og vær ytterst forsiktig ved arbeid på eller nær høyspenningssystemer og -komponenter. Send korrigeringer og tilbakemeldinger til ServiceDevelopment@teslamotors.com.

Fjerne

  1. Remove the LH rocker panel carrier. See Holder – kanalpanel – venstre (Strukturell pakke) (fjerne og skifte ut).
  2. Remove butyl patches covering LH rocker access holes
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x butyl patches, Clean excess butyl from area
  3. Install lift pad adapters onto LH rocker
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x lift pad adapters
  4. Remove the RH rocker panel carrier. See Holder – kanalpanel – venstre (Strukturell pakke) (fjerne og skifte ut).
  5. Remove butyl patches covering RH rocker access holes
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x butyl patches, Clean excess butyl from area
  6. Install lift pad adapters onto RH rocker
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x lift pad adapters
  7. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    Merk
    Verify jack locations prior to lifting vehicle, ONLY place on lifting points at front and rear of rocker panels
  8. Open LH front door
  9. Lower LH front window
  10. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  11. Remove bolt securing frunk to washer fluid reservoir neck
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 5 Nm
  12. Release washer tank neck from washer tank and set aside
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x O-ring, No need to remove hose from neck
  13. Remove HEPA filter assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 10mm, 5 Nm, Pivot rearward edge up and past brake reservoir, then lift up to clear frunk assembly
  14. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Merk
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  15. Disconnect LV battery connector and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
  16. Remove all four wheels. See Hjulenhet (fjerne og skifte ut).
  17. Release LH front wheel liner from HV battery
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x clip, 1x bolt, 10mm, 5 Nm
  18. Remove the LH front fender garnish. See Pynteelement – skjerm – foran – venstre (fjerne og skifte ut).
  19. Remove the LH front wheel arch liner. See Innerskjerm – foran – venstre (Strukturell pakke) (fjerne og skifte ut).
  20. Remove the LH rear wheel arch liner. See Innerskjerm – bak – venstre (Strukturell pakke) (fjerne og skifte ut).
  21. Release clipping points securing compressor HV harness to front of vehicle body
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x clips, Take note of original routing
  22. Release clipping points securing compressor HV harness to side of vehicle body
    Informational PurposesAn informational icon, calling your attention
    Merk
    8x clips, Release all clipping points
  23. Release side sill brake pipe assembly from LH front junction block
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x nuts, 12mm, 16 Nm, Front brake pipe B and C bundle does not detach from junction block
  24. Release rear brake lines from LH rear junction block
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x nuts, 12mm, 16 Nm, Side sill brake pipe assembly does not detach from junction block
  25. Remove bolt securing LH rear junction block to body
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 6 Nm
  26. Release side sill brake pipe assembly from clips
    Informational PurposesAn informational icon, calling your attention
    Merk
    7x clips, Do not bend pipe
  27. Remove side sill brake pipe assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x stud, Release LH rear junction block from body stud then remove assembly from front wheel well

Montere

  1. Position side sill brake pipe assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x stud, Position assembly onto front wheel well then secure LH rear junction block onto body stud
  2. Secure side sill brake pipe assembly onto clips
    Informational PurposesAn informational icon, calling your attention
    Merk
    7x clips, Do not bend pipe, Start with front clip and align pipes with LH front junction block
  3. Install bolt securing LH rear junction block to body
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 6 Nm
  4. Secure rear brake lines onto LH rear junction block
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x nuts, 12mm, 16 Nm, Side sill brake pipe assembly does not detach from junction block
  5. Secure side sill brake pipe assembly onto LH front junction block
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x nuts, 12mm, 16 Nm, Front brake pipe B and C bundle does not detach from junction block
  6. Install clipping points securing compressor HV harness to side of vehicle body
    Informational PurposesAn informational icon, calling your attention
    Merk
    8x clips, Fully secure all clips and route harness as needed
  7. Install clipping points securing compressor HV harness to front of vehicle body
    Informational PurposesAn informational icon, calling your attention
    Merk
    5x clips, Return to original routing, Verify fully secured
  8. Lower vehicle for access to underhood area
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  9. Connect first responder loop and LV battery
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
  10. Fill brake bleeder reservoir to full level
  11. Clean area around brake fluid reservoir and remove brake reservoir cap
  12. Top off brake fluid reservoir
    Informational PurposesAn informational icon, calling your attention
    Merk
    Top off brake fluid as needed
  13. Install pressure bleeder adapter onto reservoir
  14. Set brake bleed reservoir pressure to 30 psi
    Informational PurposesAn informational icon, calling your attention
    Merk
    Connect power supply to bleeder and turn on the power, Set pressure to 30 psi, Attach brake bleed reservoir to brake bleed adapter
  15. Connect to vehicle using Toolbox 3.0
    Informational PurposesAn informational icon, calling your attention
    Merk
    Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle. https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)
  16. Select Actions/Autodiag and search for "bleed"
  17. Remove bleeding valve covers and install the fluid catching bottle to LH front brake caliper outer bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x covers
  18. Open LH front brake caliper outer bleeding valve then click the play button next to "PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
    • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
    • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
    " and select Run to start the ESP, then close the bleeding valve once the pump stop running, then repeat the process for inner bleeding valve, and then lastly repeat the process for outer bleeding valve again
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  19. Repeat the above step till clear fluid and no air bubbles come out of the LH front brake caliper bleeding valve
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  20. Remove the fluid catching bottle, Torque LH front brake caliper bleeding valves then install covers
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  21. Remove bleeding valve covers and install the fluid catching bottle to RH front brake caliper outer bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x covers
  22. Open RH front brake caliper outer bleeding valve then Click the play button next to "PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
    • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
    • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
    " and select Run to start the ESP, then close the bleeding valve once the pump stop running, then repeat the process for inner bleeding valve, and then lastly repeat the process for outer bleeding valve again
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  23. Repeat the above step till clear fluid and no air bubbles come out of the RH front brake caliper bleeding valves
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  24. Remove the fluid catching bottle, Torque RH front brake caliper bleeding valves and install covers
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers
  25. Remove bleeding valve cover and install the fluid catching bottle to RH rear brake caliper bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x cover
  26. Open RH rear brake caliper bleeding valve then Click the play button next to "PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
    • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
    • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
    " and select Run to start the ESP, then close the bleeding valve once the pump stop running
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  27. Repeat the above step till clear fluid and no air bubbles come out of the RH rear brake caliper bleeding valve
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  28. Remove the fluid catching bottle, Torque RH rear brake caliper bleeding valve and install cover
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  29. Remove bleeding valve cover and install the fluid catching bottle to LH rear brake caliper bleeding valve before starting the ESP
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x cover
  30. Open LH rear brake caliper bleeding valve then Click the play button next to "PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
    • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
    • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
    " and select Run to start the ESP, then close the bleeding valve once the pump stop running
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  31. Repeat the above step untill clear fluid and no air bubbles come out of the LH rear brake caliper bleeding valve
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  32. Remove the fluid catching bottle, Torque LH rear brake caliper bleeding valve and install cover
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper
  33. Power off brake bleed reservoir and detach brake bleed reservoir from brake bleed adapter
  34. Remove pressure bleeder adapter from reservoir
  35. Check fluid level
    Informational PurposesAn informational icon, calling your attention
    Merk
    Top off if necessary
  36. Install brake reservoir cap
  37. Pump the brake pedal a few times to ensure the brake pedal feels normal
  38. Bruke Toolbox 3:
    1. Velg fanen Actions (Handlinger), og søk etter «Stiffness» (Stivhet).
    2. Velg ODIN-rutinen TEST_BRAKE_X_STIFFNESS-TEST-SERVICEvia Toolbox: (link)via Service Mode: Chassis ➜ Brakes ➜ Brake Stiffness Test, og klikk deretter på koblingen til rutinen.
    3. Hvis bremseklossene eller rotorene er skiftet ut, velger du UNBURNISHED (IKKE KJØRT INN) under «Action_Type». I alle andre tilfeller velger du BURNISHED (KJØRT INN).
    4. Klikk på RUN (KJØR) og la rutinen gjøre seg ferdig.
      Informational PurposesAn informational icon, calling your attention
      Merk
      Ikke trykk inn bremsepedalen under testen.
  39. Remove ethernet cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
  40. Raise vehicle partially and lower lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Merk
    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  41. Install the LH rear wheel arch liner. See Innerskjerm – bak – venstre (Strukturell pakke) (fjerne og skifte ut).
  42. Install the LH front wheel arch liner. See Innerskjerm – foran – venstre (Strukturell pakke) (fjerne og skifte ut).
  43. Install all four wheels. See Hjulenhet (fjerne og skifte ut).
  44. Install HEPA filter assembly
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 10mm, 5 Nm, Pivot forward edge down past frunk assembly, then carefully move rear edge past brake reservoir and into position
  45. Install washer tank neck to washer tank
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x O-ring, Ensure washer hose is properly routed after installation
  46. Secure frunk to washer fluid reservoir neck
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 10mm, 5 Nm
  47. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  48. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Merk
    Lower rack arms fully and remove from under vehicle
  49. Raise LH front window
  50. Close LH front door
  51. Remove lift pad adapters from LH rocker
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x lift pad adapters
  52. Install butyl patches onto LH rocker access holes
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"
  53. Remove the LH rocker panel carrier. See Holder – kanalpanel – venstre (Strukturell pakke) (fjerne og skifte ut).
  54. Remove lift pad adapters from RH rocker
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x lift pad adapters
  55. Install butyl patches onto RH rocker access holes
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"
  56. Install the RH rocker panel carrier. See Holder – kanalpanel – venstre (Strukturell pakke) (fjerne og skifte ut).