20/12/2022 14:37:57

Bremselinjer – hovedsylinder til ABS (Strukturell pakke) (venstrestyrt) (fjerne og skifte ut)

Korrigeringskode 33034012 1.62 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Fjerne

  1. Open the LH front door and lower the LH front window.
  2. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  3. Remove the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
  4. Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  5. Remove the 12V battery. See 12 V-/lavspenningsbatteri (fjerne og skifte ut).
  6. Remove front aero shield. See Panel – luftskjerm – foran (Strukturell pakke) (fjerne og skifte ut).
  7. Disconnect the electrical connector from the ABS unit.
  8. Position the oil drain under the ABS unit.
  9. Loosen the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  10. Loosen the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  11. Place an absorbent material beneath the brake booster and reservoir area.
  12. Using a brake fluid syringe, remove the brake fluid from the reservoir.
  13. Loosen the nut that attaches the secondary brake line to the master cylinder, and then remove the secondary brake line.
    16 Nm (11.8 lbs-ft)
  14. Loosen the nut that attaches the primary brake line to the master cylinder, and then remove the primary brake line.
    16 Nm (11.8 lbs-ft)
  15. Release the primary and secondary brake lines from the brake line bundle clip.
  16. Loosen the harness clip that attaches the master cylinder brake lines to the rear of the hydraulic control unit bracket.
  17. Route the master cylinder brake lines towards the front controller, and then remove the master cylinder brake line bundle from the vehicle.

Montere

  1. Place the master cylinder brake line bundle into position for installation
  2. Install the secondary brake line to the master cylinder, and then fasten the nut that attaches the secondary brake line.
    16 Nm (11.8 lbs-ft)
  3. Install the primary brake line to the master cylinder, and then fasten the nut that attaches the primary brake line.
    16 Nm (11.8 lbs-ft)
  4. Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
  5. Install the harness clip that attaches the master cylinder brake lines to the rear of the hydraulic control unit bracket.
  6. Attach the primary and secondary brake lines to the brake line bundle clip.
  7. Fasten the nut that attaches the master cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  8. Fasten the nut that attaches the primary cylinder secondary brake line to the ABS unit.
    16 Nm (11.8 lbs-ft)
  9. Clean the ABS unit surface of residual brake fluid.
  10. Remove the oil drain container from underneath vehicle
  11. Reconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  12. Bleed the brakes. See Lufte/skylle bremsevæske
  13. Install the front aero shield. See Panel – luftskjerm – foran (Strukturell pakke) (fjerne og skifte ut).
  14. Install the HEPA filter. See Enhet – filter – HEPA (fjerne og skifte ut).
  15. Install the underhood storage unit. See Oppbevaringsrom under panser (fjerne og skifte ut).
  16. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  17. Perform a test drive.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Per current FRT (00040100) 0.3 hrs, If alignment was adjusted verify tracking, If DAS components were adjusted verify operation, If brakes were serviced perform burnishing