2026-09-08

Basic Vehicle Inspection (Inspection)

Korrigeringskode 00030700 FRT 0.90 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og dens tilhørende FRT alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for mer informasjon om FRT-er og hvordan de lages. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

  • 2026-06-18: Released new procedure.
Merk
Denne prosedyren beskriver hvordan du utfører en grunnleggende inspeksjon av kjøretøyet. Fyll ut SC-26-00-006 mens du utfører denne prosedyren.

Fjern

  1. Open all doors from the exterior. Verify that the door operates normally and does not do any of the following:
    • Collide with the body or brightwork
    • Produce unusual noises such as creaks, groans, or clicks
    • Pause or fail to fully open
  2. Function check all windows from the LH front switch. Document any abnormal operation or noises.
  3. Function check exterior lights. Verify that the following lights operate normally:
    • Headlights (LH and RH)
    • Fog lights (LH and RH)
    • Taillights (LH and RH)
    • Center high mount stopping light (third brake light)
    • Reverse lights (LH and RH)
    • Side repeaters (LH and RH)
    • Front turn signals (LH and RH)
    • Rear turn signals (LH and RH)
  4. Close the door and hood, then function check the windshield wipers and spray jets. Verify the following:
    • The wipers and jets function
    • The wipers move in a full range of motion
    • The wipers move at all speeds
    • The wipers do not interfere with other components
    • The wipers do not produce abnormal noises such as creaks, groans, and clicks
    • The wipers do not pause
  5. Honk the horn. Verify that both high- and low-tone horns produce sound.
  6. Open the hood.
  7. Remove the rear apron
    Merk
    14x clips
  8. Visually inspect the brake fluid level.
  9. Visually inspect the coolant level. Ensure that the fluid level is at the Max line. Top off as necessary.
  10. Remove the front aeroshield. See Panel – luftskjerm – foran (Strukturell pakke) (fjerne og skifte ut) or Panel – luftskjerm – foran (Uten strukturell pakke) (fjerne og skifte ut).
  11. Install the LH and RH suspension covers. See Deksel – fjæring bak – venstre (fjerne og skifte ut).
  12. Remove the rear aeroshield. See Panel – luftskjerm – bakre (fjerne og skifte ut).
  13. Check tire pressures and adjust to specification as necessary. Inspect tires and wheels for damage or deformities.
    Merk
    Refer to the "Tire and Loading Information" label located on the driver side B-pillar.
  14. Record outer, center, and inner tread depths for all tires.
    ADVARSEL
    Measure the circumferential tire grooves only. Do not place the tire tread gauge probe on the molded treadwear indicators. Recommend replacement if tread depth is 4/32in (3mm) or less.
    Merk
  15. Inspect all brake pads.
    Merk
    Recommend replacement if 2mm or less. Check both inboard and outboard pads
  16. Inspect all brake rotors for excessive wear or rust. See Bremser for minimum specs.
  17. Perform visual inspection of all brake pipes and hoses
    Merk
    Pay special attention to brake junction points
  18. Inspect the front and rear vehicle underside components.
    Merk
    Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
  19. Inspect the underside of vehicle for fluid leaks.
  20. Inspect the steering components.
    Merk
    Check steering gear joints and electrical connections. Verify components are not bent or damaged
  21. Visually inspect the HV battery enclosure.
    Merk
    Check for any dents, scrapes, or other damage
  22. Inspect the front suspension components
    Merk
    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
  23. Inspect the rear suspension components
    Merk
    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
  24. Install the rear aeroshield. See Panel – luftskjerm – bakre (fjerne og skifte ut).
  25. Install the LH and RH suspension covers. See Deksel – fjæring bak – venstre (fjerne og skifte ut).
  26. Install the front aeroshield. See Panel – luftskjerm – foran (Strukturell pakke) (fjerne og skifte ut) or Panel – luftskjerm – foran (Uten strukturell pakke) (fjerne og skifte ut).
  27. Lower the vehicle fully.
    Merk
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  28. Remove the vehicle from the lift.
    Merk
    Lower the rack arms fully and remove them from under vehicle.
  29. Fill the washer reservoir with fluid.
  30. Install the rear apron
    Merk
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
  31. Close the hood.
  32. Perform a road test.
    1. Perform a series of ABS-active stops and ensure proper brake pedal feel and performance.
      Merk
      The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present.
    2. Check the vehicle alignment.
      Merk
      Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension. On a flat road, at 35 mph (56 kph), the vehicle should not pull in either direction.