18/12/2023 13:00:37

Samleskinne – uttak – positiv – hurtiglading – høyspenningsbatteri (strukturell pakke) (fjerne og skifte ut)

Korrigeringskode 16307202 1.92 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Denne prosedyren er et UTKAST. Selv om den har blitt godkjent, kan det hende at advarsler og forholdsregler mangler. Følg sikkerhetskravene, og vær ytterst forsiktig ved arbeid på eller nær høyspenningssystemer og -komponenter. Send korrigeringer og tilbakemeldinger til ServiceDevelopment@teslamotors.com.
  1. Open all four doors
  2. Lower all four windows
  3. Place vehicle in service mode with touchscreen
    Informational PurposesAn informational icon, calling your attention
    Merk
    Hold Tesla T icon at top of center display for four seconds and then type "service" into dialog box
  4. Remove the ancillary bay cover. See Hette – tilleggsbrønn (Strukturell pakke) (fjerne og skifte ut).
  5. Fjern den pyrotekniske batterifrakoblingen. Se Pyroteknisk batterifrakobling (Strukturell pakke) (fjerne og montere).
  6. Disconnect fast charge contactor
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Push on both side of connector to release tabs and pull upward
  7. Remove bolt securing AC filter harness to negative DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  8. Remove bolt securing AC filter harness positive DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  9. Release AC filter harness from tray
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips
  10. Remove FC contactor cover
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x securing tabs
  11. Remove bolts securing FC positive outlet jumper
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  12. Remove FC positive outlet jumper from ancillary bay
  13. Position FC positive outlet jumper onto ancillary bay
  14. Install bolts securing FC positive outlet jumper
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x bolts, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  15. Perform Hioki measurement at the joint from FC positive outlet jumper busbar to DC positive link busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1 HV joint, 60µΩ or less
  16. Install FC contactor cover
    Informational PurposesAn informational icon, calling your attention
    Merk
    3x securing tabs
  17. Install bolt securing AC filter harness positive DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Install new bolt
  18. Install bolt securing AC filter harness to negative DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Install new bolt
  19. Perform Hioki impedance measurement at joint from AC filter harness to positive DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x HV joint, 150µΩ or less
  20. Perform Hioki impedance measurement at joint from AC filter harness to negative DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x HV joint, 150µΩ or less
  21. Secure AC filter harness onto tray
    Informational PurposesAn informational icon, calling your attention
    Merk
    2x clips
  22. Connect fast charge contactor
    Informational PurposesAn informational icon, calling your attention
    Merk
    1x connector, Push on both side of connector to release tabs and pull upward
  23. Mål spenningen over monteringspunktene for den pyrotekniske batterifrakoblingen, og monter deretter den pyrotekniske batterifrakoblingen. Se Pyroteknisk batterifrakobling (Strukturell pakke) (fjerne og montere).
  24. Install the ancillary bay cover. See Hette – tilleggsbrønn (Strukturell pakke) (fjerne og skifte ut).
  25. Exit Service Mode through UI
    Informational PurposesAn informational icon, calling your attention
    Merk
    Controls > Service Mode > Exit Service Mode
  26. Raise all four windows
  27. Close all four doors
    Informational PurposesAn informational icon, calling your attention
    Merk
    If 12V is powered up, Unlatch rear doors before closing