01/03/2023 07:38:16

Teppe – foran – høyre (7-seter) (fjerne og skifte ut)

Korrigeringskode 15303112 0.66 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Fjerne

  1. Open all the doors and lower all the windows.
  2. Remove the passenger footwell cover assembly from the vehicle. See Deksel – fotbrønn – passasjer (venstrestyrt) (fjerne og skifte ut).
    Informational PurposesAn informational icon, calling your attention
    Merk
    It is not necessary to remove components from the assembly after removal.
  3. Remove the RH center console side panel. See Sidepanel – midtkonsoll – venstre (fjerne og skifte ut).
  4. Remove the bolts that attach the RH front of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  5. Remove the RH middle A-pillar trim. See Kledning – A-stolpe – midten – venstre (fjerne og skifte ut).
  6. Remove the RH lower A-pillar trim. See Deksel – A-stolpe – nedre – venstre (fjerne og skifte ut).
  7. Release the RH front door seal from the body.
  8. Release the clip that attaches the RH front carpet to the body near the front of the RH door opening.
    Figur 1. LH shown; RH similar
  9. Fold the front of the RH front carpet rearward so that the RH body controller module and its surrounding connectors are exposed.
  10. Remove and discard the bolts (x2) that attach the front of the 1st row RH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    • 3/8 in std skralle med fleksibelt hode
    • 3/8 in momentnøkkel med fleksibelt hode (kun montering)
    Figur 2. LH shown; RH similar
  11. Move the seat fully forward.
  12. Raise RH front seat cushion to the maximum height.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Adjust the seat back if needed to avoid contacting the headliner.
  13. Sett utløsningsnøkkelen for sikkerhetsbeltet (1133787-00-A) inn nederst i beltestrammerkoblingen for å løsne sikkerhetsbeltet fra strammeren.
  14. Remove the center console lower rear panel. See Panel – nede bak – midtkonsoll (fjerne og skifte ut).
  15. Remove the bolt that attaches the RH rear of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  16. Remove and discard the bolts (x2) that attach the rear of the 1st row RH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    • 3/8 in std skralle med fleksibelt hode
    • 3/8 in momentnøkkel med fleksibelt hode (kun montering)
    Figur 3. LH shown; RH similar
  17. Move RH front seat to the middle of the track at the most upright position for easy removal.
  18. Remove the LH center console side panel. See Sidepanel – midtkonsoll – venstre (fjerne og skifte ut).
  19. Remove the bolts that attach the LH front of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  20. Move the driver seat forward and the cushion to maximum height.
  21. Remove the bolt that attaches the LH rear of the center console to the body.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  22. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  23. Remove the HEPA filter assembly. See Enhet – filter – HEPA (fjerne og montere).
  24. Disconnect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  25. Release the connector lock, and then disconnect the RH front seat harness from the RH body controller.\
    Informational PurposesAn informational icon, calling your attention
    Merk
    Squeeze the release tab on the LH front seat connector lock, and then swing the lock away from the connector to release the lock.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Do not pull on the connector too hard. If the connector does not easily disconnect from the LH body controller, the lock is still engaged.
  26. Release the retaining clips (x2), and then remove the RH front seat harness from the RH footwell support bracket.
  27. Release the clips (x3) that attach the RH front seat harness to the RH front seat harness guide.
  28. Pull the RH front seat harness out from under the RH front carpet.
  29. With assistance, remove the seat from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Lift the seat, tilt the seat back, rotate the cushion toward the front door, and remove the seat from the vehicle, cushion first.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Take care not to damage the upholstery or trim while removing the seat.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    If reinstalling the seat, place the seat in an area where it is not likely to be tipped over or otherwise damaged.
    Figur 4. LH shown; RH similar
  30. Disconnect the electrical connector that is located at the RH front of the center console.
  31. Disconnect the electrical connector from the rear of the center console.
  32. With an assistant, remove the center console from the vehicle as follows:
    1. Tilt the rear of the center console upwards.
    2. Pull the center console towards the rear of the vehicle.
    3. Tilt the front of the center console upwards.
    4. Remove the center console through the passenger front door.
  33. Remove the clips (x2) that attach the RH front carpet to the vehicle.
  34. Lift up the rear edge of the RH front carpet, and then slide the carpet out towards the rear of the vehicle to remove it.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Be careful to avoid the foam below catching on the seat risers.

Montere

  1. Position the RH front carpet into the vehicle.
  2. Install the clips (x2) that attach the RH front carpet to the vehicle.
  3. With an assistant, install the center console into the vehicle as follows:
    1. Tilt the front of the center console downwards.
    2. Slide the center console towards the front of the vehicle.
    3. Tilt the rear of the center console downwards until it is in place.
  4. Connect the electrical connector that is located at the RH front of the center console.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  5. 7 Nm (5.2 lbs-ft)
    Monter boltene som fester midtkonsollen i forkant på høyre side til karosseriet.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  6. Install the RH center console side panel carpet. See Sidepanel – midtkonsoll – venstre (fjerne og skifte ut).
  7. Install the passenger footwell cover assembly. See Deksel – fotbrønn – passasjer (venstrestyrt) (fjerne og skifte ut).
  8. Connect the electrical connector in the rear of the center console.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Ensure the connector is properly installed. Perform a push-pull test before continuing this procedure.
  9. 7 Nm (5.2 lbs-ft)
    Monter bolten som fester midtkonsollen i bakkant på høyre side til karosseriet.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  10. 7 Nm (5.2 lbs-ft)
    Monter bolten som fester midtkonsollen i bakkant på venstre side til karosseriet.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  11. Install the center console lower rear panel. See Panel – nede bak – midtkonsoll (fjerne og skifte ut).
  12. With assistance, position the 1st row LH seat in the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Take care not to damage the upholstery or trim while positioning the seat.
  13. Secure the RH front seat harness under the RH front carpet.
  14. Secure the clips (x3) that attach the RH front seat harness to the RH front seat harness guide.
  15. Install the retaining clips (x2) that attach the RH front seat harness to the RH footwell support bracket.
  16. Connect the RH front seat harness to the RH body controller, and then secure the connector lock.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure the connector and lock are fully engaged.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Perform a pull push pull test to ensure the connector and connector lock are seated.
  17. Fully the seat RH front carpet.
  18. Unfold the RH front carpet back into position, and then install the clip that attaches the carpet to the body near the front of the RH door opening.
    Figur 5. LH shown; RH similar
  19. Install the RH lower A-Pillar trim. See Deksel – A-stolpe – nedre – venstre (fjerne og skifte ut).
  20. Install the RH middle A-Pillar trim. See Kledning – A-stolpe – midten – venstre (fjerne og skifte ut).
  21. Connect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  22. Install the HEPA filter assembly. See Enhet – filter – HEPA (fjerne og montere).
  23. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  24. Move the RH front seat fully rearward.
  25. 33.5 Nm (24.7 lbs-ft)
    Sett inn nye bolter (2 stk.) for å feste forsiden av høyre sete på første rad til karosseriet.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    • 3/8 in std skralle med fleksibelt hode
    • 3/8 in momentnøkkel med fleksibelt hode (kun montering)
    Figur 6. LH shown; RH similar
  26. Move the RH front seat fully forward.
  27. Install the RH 1st row seatbelt retractor onto the pretensioner.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Når du har montert beltestrammeren i beltestrammerkoblingen igjen, gjennomfører du en trekktest for å forsikre deg om at sikkerhetsbeltet og strammeren sitter godt fast.
    Figur 7. LH shown; RH similar
  28. 33.5 Nm (24.7 lbs-ft)
    Sett inn nye bolter (2 stk.) for å feste baksiden av høyre sete på første rad til karosseriet.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • Torx Plus T45-nøkkel
    • 3/8 in std skralle med fleksibelt hode
    • 3/8 in momentnøkkel med fleksibelt hode (kun montering)
    Figur 8. LH shown; RH similar
  29. Move the RH front seat to the original position.
  30. Move the LH front seat rearward.
  31. 7 Nm (5.2 lbs-ft)
    Monter boltene som fester midtkonsollen i forkant på venstre side til karosseriet.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Bruk av følgende verktøy anbefales:
    • 10 mm nøkkel
    • 4 i forlengelse
    • ¼ in std skralle
    • ¼ in momentnøkkel (kun montering)
  32. Install the LH center console side panel carpet. See Sidepanel – midtkonsoll – venstre (fjerne og skifte ut).
  33. Move the LH front seat to the original position.
  34. Raise all the windows and close all the doors.