09/02/2024 15:06:59

Bremsekaliper – bak – par (fjerne og skifte ut)

33010522 0.84 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Warning IconA warning icon, calling your attention to a possibly risky situation
ADVARSEL
Bremsevæske løser opp lakk. Ha rene håndklær og rikelig med vann stående klart for å fjerne sølt bremsevæske av lakkerte overflater.
Informational PurposesAn informational icon, calling your attention
Merk
Avfallshåndter brukt bremsevæske i samsvar med lokale miljøforskrifter.
Informational PurposesAn informational icon, calling your attention
Merk
This procedure is applicable to both base and sport type brake calipers.
  1. Prepare the vehicle for lifting, but do not lift it at this time. See Heve bil – løftebukk med 2 stolper.
  2. Open the LH front door and lower the window.
  3. Enable Service Model via the touchscreen. See Servicemodus.
  4. Unlock the vehicle gateway. See Gateway (lås opp).
  5. Put the EPB in Service Mode: on the touchscreen, touch Chassis > Brakes > EPB Service Mode, from the drop down menus, select Both and Start, and then touch Run.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ADVARSEL
    The vehicle may roll freely.
  6. Remove LH and RH rear wheels. See Hjulenhet (fjerne og skifte ut).
  7. Disconnect the LH rear brake caliper connector.
  8. Remove the bolt that attaches the LH rear brake caliper harness bracket.
  9. Position an oil drain container under LH rear brake hose area.
  10. Remove the tube nut that attaches the LH rear brake line to the LH rear brake hose.
  11. Remove and discard the LH rear jounce hose clip.
  12. Position the oil drain container under the LH rear brake caliper area.
  13. Remove the bolt that attaches the LH rear brake hose to the LH rear brake caliper.
  14. Remove and discard the bolts (x2) that attach the LH rear brake caliper bracket to the knuckle, and then remove the brake caliper from the vehicle.
  15. Install new bolts (x2) that attach the LH rear brake caliper bracket onto the knuckle (torque 83 Nm).
    Informational PurposesAn informational icon, calling your attention
    Merk
    Mark the bolts with a paint pen after torquing.
  16. Install a new bolt and new copper washers (x2) that attach the LH rear brake hose to the LH rear brake caliper (torque 42 Nm).
    Informational PurposesAn informational icon, calling your attention
    Merk
    Mark the bolt with a paint pen after torquing.
  17. Install a new LH rear jounce hose clip to attach the hose to the body.
  18. Position the oil drain container under the LH rear brake hose area.
  19. Install the LH rear brake line tube nut to the LH rear brake hose (torque 16 Nm).
  20. Install the nut that attaches the LH rear brake caliper harness bracket (torque 5 Nm).
  21. Connect the LH rear brake caliper connector.
  22. Repeat steps 7 through 21 on the RH side of the vehicle.
  23. Bleed the LH and RH brake calipers. See Lufte bremsevæske – én kaliper.
  24. Put the vehicle into park.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Make sure that parking brakes are engaged. Putting the vehicle into Park also disables EPB Service Mode.
  25. Perform a road test and burnish the brakes. See Bremseklosser – kjøre inn.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Ensure proper brake pedal feel and performance. Add correction code 33013000 as a separate activity to the SV.