2026-10-13

Luftlekkasjetest på tilleggsbrønn (strukturell pakke)

Korrigeringskode 16100420 0.55 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og dens tilhørende FRT alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

  • 2026-09-30: Another major revision due to new procedure validation, including adapted test pressure decay values.
  • 2026-08-21: Major revision as a result of new procedure validation.
  • 2025-09-05: Cleaned up procedure and removed redundant illustration.

Procedure

  1. Perform the vehicle HV disablement procedure. See Deaktiveringsprosedyre for bilens høyspenning (Strukturell pakke)
  2. Lower the vehicle until the tires are touching the floor.
  3. If present, cut away the insulation that covers the pyro cover.
  4. Remove and discard the breather from the pyro cover.
  5. Install the air splitter hose onto the pyro cover.
  6. Close both valves on the regulator test tool, and then connect the regulator to air supply.
  7. Turn the right side regulator valve to the open position.
  8. Set the regulator to 0.300 psi.
  9. Open the left side regulator valve to inject air into the ancillary bay.
    Merk
    Allow 30 seconds fill time. Close the right side regulator valve when the pressure reaches 0.300 psi.
  10. Wait 15 seconds for the pressure to settle.
    • If pressure is below 0.285 psi, check the hose, adapter, plug fittings, and check the pressure regulator, then retest. If pressure is still below 0.285 psi, diagnose enclosure for leaks.
    • If pressure is at 0.285 psi or above, continue to the next step.
  11. Record the value of the starting pressure.
  12. Wait 30 seconds to test pressure.
  13. Record the value of the ending pressure.
  14. Subtract the ending pressure from the starting pressure.
    • If the difference is greater than 0.051 psi, then inspect the tools and retest. If the difference is still greater than 0.051 psi, then diagnose the enclosure for leaks.
    • If difference is 0.051 psi or less, then proceed with the current procedure.
  15. Disconnect the air supply from regulator tool.
  16. Remove the air splitter hose from the pyro cover.
  17. Install a new breather plug (1108907-00-B) onto the pyro cover.
  18. Raise the vehicle.
  19. Install the rear drive unit HV cable connector to the HV battery and install other components that were removed to perform the vehicle HV disablement procedure. See Deaktiveringsprosedyre for bilens høyspenning (Strukturell pakke).
    Merk
    Make sure that the lever is in the upright and open position. Carefully seat the connector and allow the lever to engage. Fully install the lever and make sure that the locking tab is locked.
  20. Connect LV power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  21. Install the 2nd row seat cushion.
    Merk
    1x connector. Slide the rear cushion rearward, then align the foam with the seat rail. Make sure that the cushion is fully seated with a push-pull test.