31/05/2023 06:33:49

Sikkerhetsbelte – andre rad – venstre (7-seter) (fjerne og skifte ut)

Korrigeringskode 20056122 0.30 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT ovenfor alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det.MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til LaborTimeFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor.

Fjerne

  1. Open the LH front door and lower the LH front window.
  2. Move the driver seat forward.
  3. Open the LH rear door and lower the LH rear window.
  4. Move the LH 2nd row seat back assembly forward.
  5. Open the liftgate.
  6. Remove the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  7. Disconnect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  8. Remove the rear load floor. See Gulvplate i bagasjerom – bak (fjerne og skifte ut).
  9. Release the clips (x4) that attach the LH side of the trunk sill trim to the vehicle, and then partially release the LH side of the trunk sill trim.
  10. Remove the LH load floor bracket. See Brakett – gulvplate i bagasjerom – venstre (fjerne og skifte ut).
  11. Remove the LH trunk pocket bracket. See Brakett – lomme i bagasjerom – venstre (fjerne og skifte ut).
  12. Release the upper portion of the LH trunk side trim.
  13. Release the clips (x6) that attach the upper C-pillar trim, and then set the trim aside.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Guide the front upper corner groove out of the headliner.
  14. Ta av og kasser bolten som fester det nedre sikkerhetsbeltefestet i andre rad til venstre til karosseriet.
    Tips: Bruk av følgende verktøy anbefales:
    • 15 mm nøkkel
    • 3 i forlengelse
  15. Release the clips that attach the guide bezel to the LH upper C-pillar trim, and then separate the bezel from the seat belt.
  16. Feed the seat belt through the LH upper C-pillar trim, and then remove the trim.
  17. Release the connector lock, and then disconnect the LH 2nd row seat belt connector.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Lift the red locking tab, and then release the connector.
  18. Remove and discard the bolt that attaches the LH 2nd row seatbelt to the body, and then remove the seatbelt from the vehicle.
    30 Nm (22.1 lbs-ft)
    Tips: Bruk av følgende verktøy anbefales:
    • 13 mm nøkkel

Montere

  1. Position the LH 2nd row seatbelt into the vehicle, and then install a new bolt that attaches the seatbelt to the body.
    30 Nm (22.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Merk
    Note the position of the locating tabs.
    Tips: Bruk av følgende verktøy anbefales:
    • 13 mm nøkkel
  2. Connect the LH 2nd row seat belt connector, and then engage the connector lock.
  3. Install the LH upper C-pillar trim. See Deksel – C-stolpe – øvre – venstre (fjerne og skifte ut).
  4. Connect 12V power. See 12 V-/lavspenningsstrøm (koble fra og koble til).
  5. Install the rear underhood apron. See Deksel under panser – bak (fjerne og skifte ut).
  6. Move the driver seat to the original position.
  7. Raise the LH front window and close the LH front door.
  8. Move LH 2nd row seat back to the original position.
  9. Raise the LH rear window and close the LH rear door.
  10. Close the liftgate.