2026-03-04

Tie Rod Kit - LH (Remove and Replace)

Korrigeringskode 32013202 FRT 0.48 MERK: Hvis ikke noe annet er uttrykkelig oppgitt i prosedyren, gjenspeiler korrigeringskoden og FRT oppgitt ovenfor, alt arbeidet som kreves for å gjennomføre denne prosedyren, inkludert de tilknyttede prosedyrene. Ikke stable korrigeringskoder med mindre du bli uttrykkelig bedt om det. MERK: Se Flat rate-tider for å lære mer om FRT-er og hvordan de lages. Hvis du vil gi tilbakemelding om FRT-verdier, kan du sende en e-post til ServiceManualFeedback@tesla.com. MERK: Se Personlig beskyttelse for å forsikre deg om at du bruker riktig PVU når du gjennomfører prosedyren nedenfor. MERK: Se Forholdsregler for ergonomi for trygge og sunne arbeidspraksiser.

  • 2025-12-16: Released new procedure.

Fjern

  1. Raise and support the vehicle. See Heve bil – løftebukk med 2 stolper
  2. Open LH front door
  3. Lower LH front window
  4. Remove the LH front wheel arch liner. See
  5. Remove and discard the nut that secures the LH front tie rod end to the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  6. Remove the LH front tie rod end from the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Move the rotor back and forth for easier removal.
  7. Remove and discard the large clamp from the bellows.
  8. Remove the seal clip from the bellows.
  9. Slide the bellows toward the LH outer tie rod end to access the ball joint.
  10. Remove the LH tie rod assembly from the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)

Monter

  1. Turn the jam nut on the new tie rod to adjust the length and match the old tie rod before installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Count the threads on the removed tie rod, then adjust to the same count on the new one. This will make alignment adjustment easier.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Use of the following tool(s) is recommended:
    • 21 mm 12pt combination wrench
    • 14 mm 12pt combination wrench
    • Extension
  2. Install the LH inner tie rod assembly onto the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    Merk
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)
  3. Slide the bellows into the clamping position.
  4. Secure the large bellows clamp onto the bellows.
  5. Secure the bellows seal clip onto the bellows.
  6. Position the LH front tie rod end to the LH front knuckle.
  7. Install a new nyloc nut to secure the LH tie rod end to the LH front knuckle
    Informational PurposesAn informational icon, calling your attention
    Merk
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  8. Remove the LH front wheel arch liner. See
  9. Remove the vehicle from the lift. See Heve bil – løftebukk med 2 stolper
  10. Raise the windows and close the doors.
  11. Review the wheel alignment requirements and add correction code as needed. See Innrettingskrav – fjæring