2026-07-02
执行常规检查 (Inspection)
校正代码
00030700
FRT
1.02
注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时深入了解 FRT 及其创建方式。
注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：请参阅人体工程学注意事项查看安全健康的作业规程。
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
- 2026-06-18: Released new procedure.
Procedure
-
Function check LH front door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
-
Function check all windows from the master switch
注Check operation with door closed, Document any abnormal operation/noises
-
Function check LH rear door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
-
Function check RH rear door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
-
Function check RH front door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
-
Verify operation of all exterior lights
注Recommend assistance, Headlamps, fog lights, license plate, tail, brake, reverse, & side repeater
-
Engage drive rails and activate windshield washer and wiper operation
注Engage drive rails and hold down on the washer button, Verify wipers and washer is operating as intended
-
Function check horn
-
Open hood
注Via Controls > Frunk Open
-
Remove rear underhood apron
注8x clips
-
Remove LH underhood apron
注10x clips, (*Use this step for Palladium S procedures)
-
Remove RH underhood apron
注10x clips
-
Remove front underhood apron
注7x clips
-
Remove frunk access panel
注3x clips, 3x hooks, 1x connector
-
Remove frunk carpet
-
Remove frunk assembly
注4x bolts, 10mm, 5 Nm
-
Perform inspection of under hood area
注Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
-
Inspect brake fluid level
-
Inspect coolant level and top off as necessary
注Ensure that the fluid level is at the Max line, Top off fluid as required
-
Fill washer reservoir with fluid
-
Raise vehicle fully and lower lift onto locks
注Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
-
Remove front aero shield
注5x push clips
-
Release front aero shield
注9x bolts, 10mm, 6 Nm
-
Release rear aero shield
注4x push clips
-
Remove rear aero shield
注16x bolts, 10mm, 6 Nm
-
Perform inspection of vehicle underside components front and rear
注Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
-
Inspect underside of vehicle for fluid leaks
-
Perform inspection of steering components
注Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
-
Perform inspection of front suspension components
注Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
-
Perform inspection of rear suspension components
注Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
-
Inspect underside of battery for damage
-
Check tire pressures
注4x tires, Adjust to specification if necessary
-
Inspect condition of LH front tire
注Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
-
Measure and record LH front tread depth
注Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
-
Perform visual inspection of LH front brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect LH front brake rotor condition
注Check for excessive rust or wear, Minimum spec 30mm
-
Inspect condition of LH rear tire
注Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
-
Measure and record LH rear tread depth
注Record at least 3 measurements: Inner, Middle, Add line to replace if under 5/32 inch tread remaining
-
Perform visual inspection of LH rear brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect LH rear brake rotor condition
注Check for excessive rust or wear, Minimum spec 26mm
-
Inspect condition of RH rear tire
注Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
-
Measure and record RH rear tread depth
注Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
-
Perform visual inspection of RH rear brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect RH rear brake rotor condition
注Check for excessive rust or wear, Minimum spec 26mm
-
Inspect condition of RH front tire
注Tire Condition: No damage to sidewall (cuts, tears, bulges), No foreign objects in tread area, No uneven wear or sidewall cracking
-
Measure and record RH front tread depth
注Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
-
Perform visual inspection of RH front brake pads
注Perform visual inspection, Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect RH front brake rotor condition
注Check for excessive rust or wear, Minimum spec 30mm
-
Inspect brake hose condition
注Look for evidence of brake hose(s) rubbing on surrounding components, Inspect hose connections for evidence of leaks, Verify hoses are routed properly and secured to retaining brackets
-
Install rear aero shield
注16x bolts, 10mm, 6 Nm, Apply Loctite 222 onto mid aero shield bolts and install fasteners securing mid aero shield to vehicle
-
Position rear aero shield
注4x push clips
-
Secure front aero shield to vehicle
注9x bolts, 10mm, 6 Nm, Apply Loctite 222 onto front aero shield bolts
-
Install front aero shield
注5x push clips
-
Lower vehicle fully
注Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
-
Remove vehicle from lift
注Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
-
Install frunk assembly
注4x bolts, 10mm, 5 Nm
-
Install frunk carpet
注Verify carpet is properly seated under the seal
-
Install frunk access panel
注3x clips, 3x hooks, 1x connector
-
Install front underhood apron
注7x clips
-
Install RH underhood apron
注10x clips
-
Install LH underhood apron
注10x clips
-
Install rear underhood apron
注8x clips
-
Close hood
注Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
-
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance
注The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
-
Inspect vehicles alignment
注Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction