2023-04-02

Diffuser - Rear Fascia (Remove and Replace)

校正代码 12030802 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See 平均维修工时 to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure proper PPE is worn when performing the below procedure.

扭矩规格

表 1. 扭矩规格: Diffuser - Rear Fascia (Remove and Replace)
描述 扭矩值 推荐工具 重新使用/更换 备注
Bolts (x6) and nuts (x3) that attach the rear fascia diffuser to the underbody
5 Nm (3.7 lbs-ft)
  • 10 mm socket
  • Ratchet/torque wrench
  • 6 in extension
重新使用

拆卸

  1. 用双柱举升机举升车辆。请参阅Raise Vehicle - 2 Post Lift
  2. 拆下中间流线型护板。请参阅Panel - Aero Shield - Rear (Remove and Replace)
  3. 小心地拆下将牵引挂钩盖板固定至后仪表板扩散器的塑料螺钉(2 个)。
    Informational PurposesAn informational icon, calling your attention
    避免损坏塑料螺钉,因为它们是固定的。
  4. 松开将牵引挂钩盖板固定到下部后饰板扩散器的卡子(10 个),从扩散器上拆下盖板。
  5. 松开将后仪表板扩散器固定至左侧和右侧后轮拱内衬上的推拉式卡子(6 个)。
  6. 拆下将后仪表板扩散器固定至车身底部的螺栓(6 个)和螺母(3 个)。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
    • 棘轮/扭矩扳手
    • 6 英寸加长件
  7. 松开将后仪表板扩散器固定至后仪表板的锁片(8 个),从车身拆下扩散器。

安装

  1. 扣紧将扩散器连接至仪表板的锁片(8 个),再安装将后仪表板扩散器连接至车身底部的螺栓(6 个)和螺母(3 个)。
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
    • 棘轮/扭矩扳手
    • 6 英寸加长件
  2. 扣紧将后仪表板扩散器固定至左侧和右侧后轮拱内衬上的推拉式卡子(6 个)。
  3. 将牵引挂钩盖板安装至后仪表板扩散器处,再扣紧将盖板固定到扩散器上的锁片(10 个)。
  4. 小心地安装将牵引挂钩盖板固定至后仪表板扩散器的塑料螺钉(2 个)。
  5. 安装中间流线型护板。请参阅Panel - Aero Shield - Rear (Remove and Replace)
  6. 将车辆驶离举升机。请参阅Raise Vehicle - 2 Post Lift