2026-09-29

同轴电缆 – 侧转向灯 - 前 – 右（更换） ((拆卸和更换))

校正代码 17403112 FRT 1.38 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
  • 2026-07-09: Released new procedure.

Overlay

  1. Open both front doors and lower both front windows.
  2. Remove the wiper module. See 雨刮器模块（拆卸和更换）.
  3. Remove RH mid A-pillar trim
    注
    1x clip, 2x tabs
  4. Remove RH lower A-pillar trim
    注
    7x clips, Partially release seal if needed
  5. Remove RH footwell cover
    注
    3x magnets, 1x connector, 4x datums
  6. Move RH front seat backward
  7. Remove RH front floor mat
  8. Remove RH console side carpet
    注
    11x clips
  9. Fold RH front cabin carpet aside for access
    注
    Caution not to damage styrofoam of carpet
  10. Release harness from RH footrest panel
    注
    1x clip
  11. Remove RH footrest panel
    注
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  12. Disconnect brown fakra connection from car computer
    注
    1x connector, X836
  13. Raise and support vehicle
    注
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  14. Remove RH front wheel cap
    注
    Lift every other spoke at a time until cap is released from rim
  15. Loosen RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  16. Raise vehicle partially and lower onto locks
    注
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  17. Remove RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  18. Partially release rear portion of RH rear wheel liner
    注
    5x clips, 1x fan clip, Move liner aside
  19. Disconnect RH front repeater
    注
    2x connectors
  20. Release RH grommet from body
    注
    With a razor blade, carefully cut the electrical tape away exposing the rubber dust boot
  21. Remove electrical tape securing harness bundle to rubber dust boot
  22. Remove the connector from the coax cable
    注
    Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
  23. Apply harness tape onto RH coax overlay cable before installation
    注
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  24. Position RH coax overlay cable into place, Place through RH wheel liner and dust boot towards interior cabin
    注
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  25. Pull RH coax overlay cable through bulkhead and into interior cabin
    注
    Pull harness toward car over car computer
  26. Position RH coax overlay cable onto harness, Secure cable onto car computer harness
    注
    3x zip-ties, Trim off excess material after harness has been secured
  27. Secure coax overlay through RH wheel liner and frunk harness
    注
    4x zip-ties, Trim off excess material after harness has been secured
  28. Depin the RH side coax cable (Terminal 1) from the connector X846
    注
    Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  29. Remove the coax cable from the Connector X846
    注
    Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
  30. Insert coax overlay terminal into connector X846
  31. Insert the connector locking tab and reconnect X846 together
  32. Connect brown fakra connection onto car computer
    注
    1x connector, X836
  33. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    注
    Cut the coax connector only
  34. Connect RH front repeater
    注
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  35. Secure RH grommet onto body
    注
    Use electrical tape to wrap the end of the dust boot
  36. Secure rear portion of RH rear wheel liner
    注
    5x clips, 1x fan clip, Secure liner
  37. Install RH front wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  38. Lower vehicle until tires are touching ground
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  39. Torque RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  40. Install RH front wheel cap
    注
    Align valve stem with cap
  41. Remove vehicle from lift
    注
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  42. Install RH footrest panel
    注
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  43. Secure harness to RH footrest panel
    注
    1x clip
  44. Fold RH main carpet back into place
    注
    Caution not to damage styrofoam of carpet
  45. Install RH console side carpet
    注
    11x clips
  46. Install RH footwell cover
    注
    3x magnets, 4x datums, 1x connector
  47. Install RH front floor mat
  48. Install RH lower A-pillar trim
    注
    7x clips, Verify weather seal is seated properly
  49. Install RH mid A-pillar trim
    注
    1x clip, 2x tabs, Verify weather seal is seated properly
  50. Move RH front seat to original position
  51. Install the wiper module. See 雨刮器模块（拆卸和更换）.
  52. Unlock the vehicle gateway. See 网关（解锁）.
  53. Reset DAS on UI
    注
    Select "Driver Assist" > "Cameras" > "Reset DAS", Ensure all cameras and reset DAS icon turn green on UI, If not you need to investigate further why a the particular DAS component is flagging red
  54. Exit Service Mode.
  55. Raise both front windows and close both front doors.