2026-07-31

同轴电缆 - 侧转向灯 - 前 - 左（更换） ((拆卸和更换))

校正代码 17403012 FRT 1.44 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
  • 2026-07-09: Released new procedure.

Overlay

  1. Lower both front windows and open both front doors.
  2. Remove the cowl screen. See 面板 - 前围篦板（拆卸和更换）.
  3. Remove fasteners securing LH V-brace and remove assembly
    注
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm
  4. Place wipers in service mode via UI
    注
    Via Controls > Service > Wiper Service Mode, If wiper module is not in service mode then RH pivot arm will not clear V Brace crossmember
  5. Remove wiper module
    注
    3x bolts, 10mm, 8 Nm, 1x connector, Rotate module forward and up to access connector, Observe LH wiper arm pivot during removal to avoid damage to windshield, Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module, Do not attempt to test the module until it is fully installed in the vehicle
  6. Remove LH mid A-pillar trim
    注
    1x clip, 2x tabs
  7. Remove LH lower A-pillar trim
    注
    7x clips
  8. Remove LH footwell cover
    注
    1x connector, 2x magnets
  9. Move LH front seat backward
  10. Remove LH front floor mat
  11. Remove LH console side carpet
    注
    11x clips
  12. Fold LH front cabin carpet aside for full access
  13. Remove RH mid A-pillar trim
    注
    1x clip, 2x tabs
  14. Remove RH lower A-pillar trim
    注
    7x clips, Partially release seal if needed
  15. Remove RH footwell cover
    注
    3x magnets, 1x connector, 4x datums
  16. Move RH front seat backward
  17. Remove RH front floor mat
  18. Remove RH console side carpet
    注
    11x clips
  19. Fold RH front cabin carpet aside for access
    注
    Caution not to damage styrofoam of carpet
  20. Release harness from RH footrest panel
    注
    1x clip
  21. Remove RH footrest panel
    注
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  22. Disconnect brown fakra connection from car computer
    注
    1x connector, X836
  23. Raise and support vehicle
    注
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  24. Remove LH front wheel cap
    注
    Lift every other spoke at a time until cap is released from rim
  25. Loosen LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  26. Raise vehicle partially and lower onto locks
    注
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  27. Remove LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  28. Partially release rear portion of LH rear wheel liner
    注
    5x clips, 1x fan clip, Move liner aside
  29. Disconnect LH front repeater
    注
    2x connectors
  30. Release LH grommet from body
    注
    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
  31. Remove electrical tape securing harness bundle to rubber dust boot
  32. Remove the connector from the coax cable
    注
    Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
  33. Apply harness tape onto LH coax overlay cable before installation
    注
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  34. Position LH coax overlay cable into place, Place through LH wheel liner and dust boot towards interior cabin
    注
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  35. Pull LH coax overlay cable through bulkhead and into interior cabin
    注
    Pull harness toward car computer under dashboard
  36. Position LH coax overlay cable onto main dash body harness, Secure cable onto harness using zip ties
    注
    5x zip-ties, Trim off excess material after harness has been secured
  37. Secure coax overlay through LH wheel liner and frunk harness
    注
    4x zip-ties, Trim off excess material after harness has been secured
  38. Depin the RH side coax cable (Terminal 1) from the connector X846
    注
    Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  39. Insert coax overlay terminal into connector X846
  40. Remove the coax cable from the Connector X846
    注
    Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
  41. Insert the connector locking tab and reconnect X846 together
  42. Connect brown fakra connection onto car computer
    注
    1x connector, X836
  43. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    注
    Cut the coax connector only
  44. Connect LH front repeater
    注
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  45. Secure LH grommet onto body
    注
    Use electrical tape to wrap the end of the dust boot
  46. Secure rear portion of LH rear wheel liner
    注
    5x clips, 1x fan clip, Secure liner
  47. Install LH front wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  48. Lower vehicle until tires are touching ground
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  49. Torque LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  50. Install LH front wheel cap
    注
    Align valve stem with cap
  51. Remove vehicle from lift
    注
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  52. Fold LH main carpet back into place
  53. Install LH console side carpet
    注
    11x clips
  54. Install LH footwell cover
    注
    1x connector, 2x magnets
  55. Install LH lower A-pillar trim
    注
    7x clips, Verify weather seal is seated properly
  56. Install LH mid A-pillar trim
    注
    1x clip, 2x tabs, Verify weather seal is seated properly
  57. Install LH front floor mat
  58. Move LH front seat to original position
  59. Install RH footrest panel
    注
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  60. Secure harness to RH footrest panel
    注
    1x clip
  61. Fold RH main carpet back into place
    注
    Caution not to damage styrofoam of carpet
  62. Install RH console side carpet
    注
    11x clips
  63. Install RH footwell cover
    注
    3x magnets, 4x datums, 1x connector
  64. Install RH front floor mat
  65. Install RH lower A-pillar trim
    注
    7x clips, Verify weather seal is seated properly
  66. Install RH mid A-pillar trim
    注
    1x clip, 2x tabs, Verify weather seal is seated properly
  67. Move RH front seat to original position
  68. Install wiper module
    注
    3x bolts, 10mm, 8 Nm, 1x connector, Secure electrical connector first, Rotate module rearward and under windshield, Observe LH wiper arm pivot during install to avoid damage to windshield, Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module, Do not attempt to test the module until it is fully installed in the vehicle
  69. Install fasteners securing LH V-brace and secure
    注
    3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm
  70. Install the cowl screen. See 面板 - 前围篦板（拆卸和更换）.
  71. Unlock the vehicle gateway. See 网关（解锁）.
  72. Reset DAS on UI
    注
    Select "Driver Assist" > "Cameras" > "Reset DAS", Ensure all cameras and reset DAS icon turn green on UI, If not you need to investigate further why a the particular DAS component is flagging red
  73. 运行 ODIN 例行程序 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  74. Raise both front windows
  75. Close RH front door
  76. Close LH front door
    注