2023-09-01

Stabilizer Bar - Rear (Remove and Replace)

校正代码 31033102 1.08 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See 平均维修工时 to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure proper PPE is worn when performing the below procedure.

扭矩规格

表 1. 扭矩规格悬架 - 后(扭矩)
描述 扭矩值 推荐工具 重新使用/更换 备注
Nut that attaches the stabilizer bar end link to the rear stabilizer bar
55 Nm (40.6 lbs-ft)
  • 15 毫米套筒
  • 5 毫米六角
更换
Bolts (x4) that attach the rear stabilizer bar to the vehicle
30 Nm (22.1 lbs-ft)
  • 11 毫米套筒
重新使用

拆卸

  1. 举升并支撑车辆。请参阅 Raise Vehicle - 2 Post Lift
  2. 拆下左侧和右侧后车轮。请参阅Wheel Assembly (Remove and Install)
  3. 拆下中间流线型护板。请参阅Panel - Aero Shield - Rear (Remove and Replace)
  4. 拆下后饰板扩散器。请参阅Diffuser - Rear Fascia (Remove and Replace)
  5. 拆下并弃用将后平衡杆总成固定到左后平衡杆末端连杆的螺母。为 RH 平衡杆末端连杆重复这一步骤。
    Informational PurposesAn informational icon, calling your attention
    松开螺母,然后用 5 mm 六角反向固定球头。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 15 毫米套筒
    • 5 毫米六角
  6. 拆下将后平衡杆固定到副框架的螺栓(4 个),然后从车上拆下平衡杆。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 11 毫米套筒

安装

  1. 将后平衡杆放置到副框架上,然后安装将平衡杆固定到车辆的螺栓 (x4)。
    30 Nm (22.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 11 毫米套筒
  2. 将左后平衡杆末端连杆放到平衡杆总成处,安装新螺母,将连杆连接到平衡杆总成,然后用油性记号笔标记螺母。对 RH 平衡杆末端连杆重复这一步骤。
    55 Nm (40.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    调整末端连杆,对齐稳定杆。为了获得安装末端连杆的正确角度,可能需要向上/向下移动稳定杆。
    Informational PurposesAn informational icon, calling your attention
    TIp
    使用 5 毫米六角工具,防止螺柱旋转。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 15 毫米套筒
    • 5 毫米六角
  3. 安装后饰板扩散器。请参阅Diffuser - Rear Fascia (Remove and Replace)
  4. 安装中间流线型护板。请参阅Panel - Aero Shield - Rear (Remove and Replace)
  5. 安装左后和右后车轮。请参阅Wheel Assembly (Remove and Install)
  6. 将车辆驶离举升机。请参阅 Raise Vehicle - 2 Post Lift
  7. 请参阅“定位要求”表,确定是否需要进行电动助力转向 (EPAS) 定位检查 (EC) 或四轮定位检查 (AC)。如果已执行,请作为一项单独的工项添加定位检查/调整。请参阅Alignment Requirement - Suspension